-- (C) COPYRIGHT HEWLETT-PACKARD COMPANY 2006.  
--  
-- LaserJet 4730 Printer Model Specific MIB.  
--  
-- Generated on Jun. 27, 2006.  
--  
-- Company names and product names mentioned herein may be   
-- trademarks, and/or registered trademarks of their respective  
-- companies.  
--  
-- For internal and external use.  
--  
-- This MIB describes all the printer model specific  
-- objects supported by the LaserJet 4730 printer  
-- when networked connected using a JetDirect print  
-- server.  
--  
-- The following MIBs also contain objects supported  
-- by a JetDirect connected LaserJet 4730 printer:  
--  
-- rfc 1514 Host Resources MIB  
-- rfc 1759 Printer MIB  
-- rfc 1213 MIB II  
--  
-- This MIB complies with the following RFCs:  
--  
-- rfc 1157 Simple Network Management Protocol  
-- rfc 1155 Structure of Management Information  
--  
-- Notes:  
--  
-- 1) Objects containing a string which are defined in this MIB use the  
--    first two bytes to hold the symbol set used to encode the string.  
--    The Roman-8 symbol set has a hex encoding of 0x0115.  Other   
--    symbol sets are listed in the PCL 5 Comparison Guide in table  
--    C-1 Symbol Set Values.  
--  
-- 2) Some of the objects included are only supported if an accessory   
--    is installed.  These accessories include:  
--      MIO based accessories  
--      SIMM based accessories  
--      AT hard disk  
--      Paper handling accessories  
--      Adobe PostScript accessory  
LJ4730-MIB DEFINITIONS ::= BEGIN  
  
hp OBJECT IDENTIFIER ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) 11}  
netPMLmgmt OBJECT IDENTIFIER ::= { hp nm(2) system(3) netPeripheral(9) netPML(4) 2}  
  
DisplayString::= OCTET STRING  
  
device                                OBJECT IDENTIFIER ::=  { netPMLmgmt 1 }   
device-system                         OBJECT IDENTIFIER ::=  { device 1 }   
status-system                         OBJECT IDENTIFIER ::=  { device-system 2 }   
test                                  OBJECT IDENTIFIER ::=  { device-system 5 }   
processing-subsystem                  OBJECT IDENTIFIER ::=  { device 3 }   
pml                                   OBJECT IDENTIFIER ::=  { processing-subsystem 4 }   
accounting                            OBJECT IDENTIFIER ::=  { device-system 16 }   
printer-accounting                    OBJECT IDENTIFIER ::=  { accounting 1 }   
printed-media-usage                   OBJECT IDENTIFIER ::=  { printer-accounting 1 }   
scanner-accounting                    OBJECT IDENTIFIER ::=  { accounting 2 }   
scanned-media-usage                   OBJECT IDENTIFIER ::=  { scanner-accounting 1 }   
printer-color-accounting              OBJECT IDENTIFIER ::=  { accounting 3 }   
printed-media-color-usage             OBJECT IDENTIFIER ::=  { printer-color-accounting 1 }   
printed-modes-accounting              OBJECT IDENTIFIER ::=  { accounting 4 }   
printed-modes-usage                   OBJECT IDENTIFIER ::=  { printed-modes-accounting 1 }   
source-tray-accounting                OBJECT IDENTIFIER ::=  { accounting 5 }   
source-tray-usage                     OBJECT IDENTIFIER ::=  { source-tray-accounting 1 }   
destination-bin-accounting            OBJECT IDENTIFIER ::=  { accounting 6 }   
destination-bin-usage                 OBJECT IDENTIFIER ::=  { destination-bin-accounting 1 }   
destination-subsystem                 OBJECT IDENTIFIER ::=  { device 4 }   
print-engine                          OBJECT IDENTIFIER ::=  { destination-subsystem 1 }   
print-media                           OBJECT IDENTIFIER ::=  { print-engine 8 }   
media-size                            OBJECT IDENTIFIER ::=  { print-media 5 }   
print-meter                           OBJECT IDENTIFIER ::=  { print-engine 11 }   
printer-average                       OBJECT IDENTIFIER ::=  { print-meter 1 }   
control-panel-display                 OBJECT IDENTIFIER ::=  { status-system 65 }   
settings-system                       OBJECT IDENTIFIER ::=  { device-system 1 }   
interface                             OBJECT IDENTIFIER ::=  { device-system 4 }   
simm                                  OBJECT IDENTIFIER ::=  { interface 1 }   
simm1                                 OBJECT IDENTIFIER ::=  { simm 1 }   
simm1-bank                            OBJECT IDENTIFIER ::=  { simm1 6 }   
simm1-bank1                           OBJECT IDENTIFIER ::=  { simm1-bank 1 }   
simm1-bank2                           OBJECT IDENTIFIER ::=  { simm1-bank 2 }   
simm2                                 OBJECT IDENTIFIER ::=  { simm 2 }   
simm2-bank                            OBJECT IDENTIFIER ::=  { simm2 6 }   
simm2-bank1                           OBJECT IDENTIFIER ::=  { simm2-bank 1 }   
simm2-bank2                           OBJECT IDENTIFIER ::=  { simm2-bank 2 }   
job                                   OBJECT IDENTIFIER ::=  { device-system 6 }   
settings-job                          OBJECT IDENTIFIER ::=  { job 1 }   
operating-system                      OBJECT IDENTIFIER ::=  { device-system 19 }   
pdl                                   OBJECT IDENTIFIER ::=  { processing-subsystem 3 }   
settings-pdl                          OBJECT IDENTIFIER ::=  { pdl 1 }   
status-pdl                            OBJECT IDENTIFIER ::=  { pdl 2 }   
background-message                    OBJECT IDENTIFIER ::=  { status-system 37 }   
background-message1                   OBJECT IDENTIFIER ::=  { background-message 1 }   
background-message2                   OBJECT IDENTIFIER ::=  { background-message 2 }   
background-message3                   OBJECT IDENTIFIER ::=  { background-message 3 }   
background-message4                   OBJECT IDENTIFIER ::=  { background-message 4 }   
menus                                 OBJECT IDENTIFIER ::=  { print-engine 13 }   
errorlog                              OBJECT IDENTIFIER ::=  { device-system 11 }   
error1                                OBJECT IDENTIFIER ::=  { errorlog 1 }   
error2                                OBJECT IDENTIFIER ::=  { errorlog 2 }   
error3                                OBJECT IDENTIFIER ::=  { errorlog 3 }   
error4                                OBJECT IDENTIFIER ::=  { errorlog 4 }   
error5                                OBJECT IDENTIFIER ::=  { errorlog 5 }   
error6                                OBJECT IDENTIFIER ::=  { errorlog 6 }   
error7                                OBJECT IDENTIFIER ::=  { errorlog 7 }   
error8                                OBJECT IDENTIFIER ::=  { errorlog 8 }   
error9                                OBJECT IDENTIFIER ::=  { errorlog 9 }   
error10                               OBJECT IDENTIFIER ::=  { errorlog 10 }   
error11                               OBJECT IDENTIFIER ::=  { errorlog 11 }   
error12                               OBJECT IDENTIFIER ::=  { errorlog 12 }   
error13                               OBJECT IDENTIFIER ::=  { errorlog 13 }   
error14                               OBJECT IDENTIFIER ::=  { errorlog 14 }   
error15                               OBJECT IDENTIFIER ::=  { errorlog 15 }   
error16                               OBJECT IDENTIFIER ::=  { errorlog 16 }   
error17                               OBJECT IDENTIFIER ::=  { errorlog 17 }   
error18                               OBJECT IDENTIFIER ::=  { errorlog 18 }   
error19                               OBJECT IDENTIFIER ::=  { errorlog 19 }   
error20                               OBJECT IDENTIFIER ::=  { errorlog 20 }   
error21                               OBJECT IDENTIFIER ::=  { errorlog 21 }   
error22                               OBJECT IDENTIFIER ::=  { errorlog 22 }   
error23                               OBJECT IDENTIFIER ::=  { errorlog 23 }   
error24                               OBJECT IDENTIFIER ::=  { errorlog 24 }   
error25                               OBJECT IDENTIFIER ::=  { errorlog 25 }   
error26                               OBJECT IDENTIFIER ::=  { errorlog 26 }   
error27                               OBJECT IDENTIFIER ::=  { errorlog 27 }   
error28                               OBJECT IDENTIFIER ::=  { errorlog 28 }   
error29                               OBJECT IDENTIFIER ::=  { errorlog 29 }   
error30                               OBJECT IDENTIFIER ::=  { errorlog 30 }   
error31                               OBJECT IDENTIFIER ::=  { errorlog 31 }   
error32                               OBJECT IDENTIFIER ::=  { errorlog 32 }   
error33                               OBJECT IDENTIFIER ::=  { errorlog 33 }   
error34                               OBJECT IDENTIFIER ::=  { errorlog 34 }   
error35                               OBJECT IDENTIFIER ::=  { errorlog 35 }   
error36                               OBJECT IDENTIFIER ::=  { errorlog 36 }   
error37                               OBJECT IDENTIFIER ::=  { errorlog 37 }   
error38                               OBJECT IDENTIFIER ::=  { errorlog 38 }   
error39                               OBJECT IDENTIFIER ::=  { errorlog 39 }   
error40                               OBJECT IDENTIFIER ::=  { errorlog 40 }   
error41                               OBJECT IDENTIFIER ::=  { errorlog 41 }   
error42                               OBJECT IDENTIFIER ::=  { errorlog 42 }   
error43                               OBJECT IDENTIFIER ::=  { errorlog 43 }   
error44                               OBJECT IDENTIFIER ::=  { errorlog 44 }   
error45                               OBJECT IDENTIFIER ::=  { errorlog 45 }   
error46                               OBJECT IDENTIFIER ::=  { errorlog 46 }   
error47                               OBJECT IDENTIFIER ::=  { errorlog 47 }   
error48                               OBJECT IDENTIFIER ::=  { errorlog 48 }   
error49                               OBJECT IDENTIFIER ::=  { errorlog 49 }   
error50                               OBJECT IDENTIFIER ::=  { errorlog 50 }   
channel                               OBJECT IDENTIFIER ::=  { device 6 }   
display                               OBJECT IDENTIFIER ::=  { status-system 20 }   
display-status                        OBJECT IDENTIFIER ::=  { display 1 }   
id                                    OBJECT IDENTIFIER ::=  { device-system 3 }   
web-server                            OBJECT IDENTIFIER ::=  { interface 6 }   
settings-web-server                   OBJECT IDENTIFIER ::=  { web-server 1 }   
pdl-postscript                        OBJECT IDENTIFIER ::=  { pdl 4 }   
settings-prt-eng                      OBJECT IDENTIFIER ::=  { print-engine 1 }   
intray                                OBJECT IDENTIFIER ::=  { print-engine 3 }   
settings-intray                       OBJECT IDENTIFIER ::=  { intray 1 }   
ph                                    OBJECT IDENTIFIER ::=  { print-engine 7 }   
settings-ph                           OBJECT IDENTIFIER ::=  { ph 1 }   
copier                                OBJECT IDENTIFIER ::=  { device 5 }   
settings-copier                       OBJECT IDENTIFIER ::=  { copier 1 }   
pdl-pcl                               OBJECT IDENTIFIER ::=  { pdl 3 }   
source-subsystem                      OBJECT IDENTIFIER ::=  { device 2 }   
scanner                               OBJECT IDENTIFIER ::=  { source-subsystem 2 }   
settings-scanner                      OBJECT IDENTIFIER ::=  { scanner 1 }   
status-scanner                        OBJECT IDENTIFIER ::=  { scanner 2 }   
imaging                               OBJECT IDENTIFIER ::=  { print-engine 6 }   
socket-ping                           OBJECT IDENTIFIER ::=  { interface 7 }   
active-print-jobs                     OBJECT IDENTIFIER ::=  { job 2 }   
job-being-parsed                      OBJECT IDENTIFIER ::=  { active-print-jobs 1 }   
job-info                              OBJECT IDENTIFIER ::=  { job 5 }   
job-info-attribute                    OBJECT IDENTIFIER ::=  { job-info 23 }   
job-info-accounting                   OBJECT IDENTIFIER ::=  { job-info 28 }   
held-job                              OBJECT IDENTIFIER ::=  { job 7 }   
held-job-info                         OBJECT IDENTIFIER ::=  { held-job 1 }   
held-job-control                      OBJECT IDENTIFIER ::=  { held-job 2 }   
spooler                               OBJECT IDENTIFIER ::=  { source-subsystem 4 }   
settings-spooler                      OBJECT IDENTIFIER ::=  { spooler 1 }   
pjl                                   OBJECT IDENTIFIER ::=  { processing-subsystem 5 }   
mio                                   OBJECT IDENTIFIER ::=  { interface 3 }   
mio1                                  OBJECT IDENTIFIER ::=  { mio 1 }   
mio2                                  OBJECT IDENTIFIER ::=  { mio 2 }   
mio3                                  OBJECT IDENTIFIER ::=  { mio 3 }   
io                                    OBJECT IDENTIFIER ::=  { source-subsystem 1 }   
settings-io                           OBJECT IDENTIFIER ::=  { io 1 }   
ports                                 OBJECT IDENTIFIER ::=  { io 3 }   
port1                                 OBJECT IDENTIFIER ::=  { ports 1 }   
tables                                OBJECT IDENTIFIER ::=  { device 7 }   
remote-procedure-call                 OBJECT IDENTIFIER ::=  { device-system 13 }   
settings-rpc                          OBJECT IDENTIFIER ::=  { remote-procedure-call 1 }   
status-rpc                            OBJECT IDENTIFIER ::=  { remote-procedure-call 2 }   
file-system                           OBJECT IDENTIFIER ::=  { device-system 10 }   
settings-file-system                  OBJECT IDENTIFIER ::=  { file-system 1 }   
file-systems                          OBJECT IDENTIFIER ::=  { file-system 3 }   
file-system2                          OBJECT IDENTIFIER ::=  { file-systems 2 }   
file-system3                          OBJECT IDENTIFIER ::=  { file-systems 3 }   
file-system4                          OBJECT IDENTIFIER ::=  { file-systems 4 }   
resource-manager                      OBJECT IDENTIFIER ::=  { device-system 12 }   
mass-storage-resources                OBJECT IDENTIFIER ::=  { resource-manager 3 }   
mass-storage-block-driver             OBJECT IDENTIFIER ::=  { device-system 15 }   
settings-mass-storage-bd              OBJECT IDENTIFIER ::=  { mass-storage-block-driver 1 }   
status-mass-storage-bd                OBJECT IDENTIFIER ::=  { mass-storage-block-driver 2 }   
device-configure                      OBJECT IDENTIFIER ::=  { settings-system 32 }   
marking-agent-density                 OBJECT IDENTIFIER ::=  { settings-prt-eng 9 }   
status-prt-eng                        OBJECT IDENTIFIER ::=  { print-engine 2 }   
printer-calibration-dhalf             OBJECT IDENTIFIER ::=  { status-prt-eng 37 }   
printer-cal-dhalf-data                OBJECT IDENTIFIER ::=  { printer-calibration-dhalf 3 }   
printer-calibration-cpr               OBJECT IDENTIFIER ::=  { status-prt-eng 38 }   
intrays                               OBJECT IDENTIFIER ::=  { intray 3 }   
intray1                               OBJECT IDENTIFIER ::=  { intrays 1 }   
intray2                               OBJECT IDENTIFIER ::=  { intrays 2 }   
intray3                               OBJECT IDENTIFIER ::=  { intrays 3 }   
intray5                               OBJECT IDENTIFIER ::=  { intrays 5 }   
outbin                                OBJECT IDENTIFIER ::=  { print-engine 4 }   
settings-outbin                       OBJECT IDENTIFIER ::=  { outbin 1 }   
outbins                               OBJECT IDENTIFIER ::=  { outbin 3 }   
outbin1                               OBJECT IDENTIFIER ::=  { outbins 1 }   
marking-agent                         OBJECT IDENTIFIER ::=  { print-engine 5 }   
settings-marking-agent                OBJECT IDENTIFIER ::=  { marking-agent 1 }   
settings-print-media                  OBJECT IDENTIFIER ::=  { print-media 1 }   
media-info                            OBJECT IDENTIFIER ::=  { print-media 3 }   
media1                                OBJECT IDENTIFIER ::=  { media-info 1 }   
media2                                OBJECT IDENTIFIER ::=  { media-info 2 }   
media3                                OBJECT IDENTIFIER ::=  { media-info 3 }   
media4                                OBJECT IDENTIFIER ::=  { media-info 4 }   
media5                                OBJECT IDENTIFIER ::=  { media-info 5 }   
media6                                OBJECT IDENTIFIER ::=  { media-info 6 }   
media7                                OBJECT IDENTIFIER ::=  { media-info 7 }   
media8                                OBJECT IDENTIFIER ::=  { media-info 8 }   
media9                                OBJECT IDENTIFIER ::=  { media-info 9 }   
media10                               OBJECT IDENTIFIER ::=  { media-info 10 }   
media11                               OBJECT IDENTIFIER ::=  { media-info 11 }   
media12                               OBJECT IDENTIFIER ::=  { media-info 12 }   
media13                               OBJECT IDENTIFIER ::=  { media-info 13 }   
media14                               OBJECT IDENTIFIER ::=  { media-info 14 }   
media15                               OBJECT IDENTIFIER ::=  { media-info 15 }   
media16                               OBJECT IDENTIFIER ::=  { media-info 16 }   
media17                               OBJECT IDENTIFIER ::=  { media-info 17 }   
media18                               OBJECT IDENTIFIER ::=  { media-info 18 }   
media19                               OBJECT IDENTIFIER ::=  { media-info 19 }   
media20                               OBJECT IDENTIFIER ::=  { media-info 20 }   
media21                               OBJECT IDENTIFIER ::=  { media-info 21 }   
media22                               OBJECT IDENTIFIER ::=  { media-info 22 }   
media23                               OBJECT IDENTIFIER ::=  { media-info 23 }   
media24                               OBJECT IDENTIFIER ::=  { media-info 24 }   
media25                               OBJECT IDENTIFIER ::=  { media-info 25 }   
media26                               OBJECT IDENTIFIER ::=  { media-info 26 }   
media-modes                           OBJECT IDENTIFIER ::=  { print-media 4 }   
media-types                           OBJECT IDENTIFIER ::=  { print-media 8 }   
media-counts                          OBJECT IDENTIFIER ::=  { print-media 7 }   
consumables                           OBJECT IDENTIFIER ::=  { print-engine 10 }   
consumables-1                         OBJECT IDENTIFIER ::=  { consumables 1 }   
consumable-status                     OBJECT IDENTIFIER ::=  { consumables-1 1 }   
consumable-string                     OBJECT IDENTIFIER ::=  { consumables 8 }   
consumables-status                    OBJECT IDENTIFIER ::=  { consumables 5 }   
consumables-life                      OBJECT IDENTIFIER ::=  { consumables-status 1 }   
webserver-proc-sub                    OBJECT IDENTIFIER ::=  { processing-subsystem 9 }   
settings-webserver                    OBJECT IDENTIFIER ::=  { webserver-proc-sub 1 }   
firmware-download                     OBJECT IDENTIFIER ::=  { device-system 18 }   
upgradable-devices                    OBJECT IDENTIFIER ::=  { device-system 20 }   
  
  
perm-store-init-occurred OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object will set the cAllPermDevices bit when a full perm		  
               storage initialization occurs (as would be the case for a brand		  
               new system or as a result of a powerup key sequence or		  
               <<hidden>> object request). If only one		  
               device was initialized (as would be the case if a disk were		  
               added to an existing system or a formatter were swapped out),		  
               then only the appropriate collection bits will be returned. If		  
               there are no collection bits set then this indicates that no		  
               initialization took place."  
::={ status-system 10 }  
                
                
                
                
                
printed-media-simplex-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..930576247)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of simplex pages printed in this media size.  
               Additional information:  
               The 5 usage (simplex/duplex count, simplex/duplex click  
               charge and paper size total) objects described here and  
               below detail the usage for the printer for each paper  
               size defined in the PCL Implementor's Guide and in the  
               Media Size Table in the hpmib.txt.  The OID binding is  
               based on the click attribute and paper size.  
               For example:  
                 
               The format for the OID is as follows:  
                 
               3.4.1.5.x.y  
               <-----> | |  
               |    |  \  
               /     |  paper size  
               /       \  
               PRINTER-CLICK_TOTALS ROOT   \  
               OID                      click attribute 1..5  
                 
               x values are 1..5:  
                 
               1) simplex count  
               2) simplex click charge  
               3) duplex count  
               4) duplex click charge  
               5) printer or scanner paper size total (i.e. depends if the  
               root OID is referrring to the printer or scanner).  
                 
               y : paper size as defined in the Media Size Table in the  
               hpmib.txt "  
::={ printed-media-usage 1 }  
                
                
printed-media-simplex-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Charge for each simplex page printed in this media size."  
::={ printed-media-usage 2 }  
                
                
printed-media-duplex-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..930576247)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of duplex pages printed in this media size."  
::={ printed-media-usage 3 }  
                
                
printed-media-duplex-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Charge for each duplex page printed in this media size.  
               Additional information:  
               The click charges for duplex printed media."  
::={ printed-media-usage 4 }  
                
                
printed-media-total-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The total charge for pages printed in this media size."  
::={ printed-media-usage 5 }  
                
                
printed-media-maximum-pixels-per-page OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The number of pixels required to completely fill a page of this		  
               media size. The device POS will specify the resolution at which		  
               this pixel count was calculated.  
               Additional information:  
               The number of pixels required to fill a page of a  
               specific media size.  The OID binding is the media  
               size you to query for.  Only media sizes which the  
               printer supports will be available."  
::={ printed-media-usage 6 }  
                
                
printed-media-combined-total OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of letter equivalently weighted pages both color		  
               and mono combined with this printer.  
               Additional information:  
               The combined total per page size of simplex and duplex  
               color pages plus simplex and duplex mono pages."  
::={ printed-media-usage 7 }  
                
                
printed-media-dimplex-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..930576247)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of mono dimplex pages printed in this media size.		  
               A dimplex page is one that has been printed in duplex mode but		  
               the back side is blank. Dimplex pages occur when the printer		  
               firmware inserts a blank page in order to complete a duplexed		  
               job which is sent to the printer with an odd number of pages."  
::={ printed-media-usage 10 }  
                
                
usage-printer-total-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total printer charge for all paper sizes printed."  
::={ printer-accounting 2 }  
                
                
usage-average-toner-coverage OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Reports the average toner area coverage of all pages printed		  
               over the life of the device. Counts pixels on each page,		  
               divides pixel count by pixels possible on a page to give the		  
               percentage of coverage, and keeps a rolling average percent		  
               weighted by area printed."  
::={ printer-accounting 3 }  
                
                
usage-staple-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..930576247)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of staples used."  
::={ printer-accounting 4 }  
                
                
usage-instructions-line1 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..40))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The first line of usage instructions for the device		  
               user.Appears on Line 1 of the usage page."  
::={ printer-accounting 5 }  
                
                
usage-instructions-line2 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..40))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The second line of usage instructions for the device		  
               user.Appears on Line 1 of the usage page."  
::={ printer-accounting 6 }  
                
                
usage-instructions-line3 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..40))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The third line of usage instructions for the device		  
               user.Appears on Line 1 of the usage page."  
::={ printer-accounting 7 }  
                
                
usage-instructions-line4 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..40))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The fourth line of usage instructions for the device		  
               user.Appears on Line 1 of the usage page."  
::={ printer-accounting 8 }  
                
                
printed-modes-usage-total OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION " This object reports the total color and mono print modes usage		  
               for the life of the printer. This value is reported on the		  
               usage page."  
::={ printer-accounting 9 }  
                
                
source-tray-usage-total OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object reports the total source tray usage for the life of		  
               the printer. This value is reported on the usage page."  
::={ printer-accounting 10 }  
                
                
destination-bin-usage-total OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object reports the total destination bin usage for the		  
               life of the printer. This value is reported on the usage page."  
::={ printer-accounting 11 }  
                
                
usage-printer-mono-total-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total printer charge for all paper sizes printed in monochrome		  
               only.  
               Additional information:  
               This is the total charge over the range of all  
               supported media sizes for duplex and simplex mono  
               pages."  
::={ printer-accounting 12 }  
                
                
usage-printer-color-total-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total printer charge for all paper sizes printed in color		  
               only.  
               Additional information:  
               This is the total charge over the range of all  
               supported media sizes for duplex and simplex color  
               pages."  
::={ printer-accounting 13 }  
                
                
scanned-media-simplex-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..930576247)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of simplex pages scanned, for this media size.  
               Additional information:  
               The 5 usage (simplex/duplex count, simplex/duplex click  
               charge and paper size total) objects described here and  
               below detail the usage for the scanner for each paper  
               size defined in the PCL Implementor's Guide and in the  
               Media Size Table in the hpmib.txt.  The OID binding is  
               based on the click attribute and paper size.  
               For example:  
                 
               The format for the OID is as follows:  
                 
               3.4.1.5.x.y  
               <-----> | |  
               |    |  \  
               /     |  paper size  
               /       \  
               PRINTER-CLICK_TOTALS ROOT   \  
               OID                      click attribute 1..5  
                 
               x values are 1..5:  
                 
               1) simplex count  
               2) simplex click charge  
               3) duplex count  
               4) duplex click charge  
               5) printer or scanner paper size total (i.e. depends if the  
               root OID is referrring to the printer or scanner).  
                 
               y : paper size as defined in the Media Size Table in the  
               hpmib.txt  
                 
               The click charge objects are of data type real and have a single  
               digit of precision. Setting these objects to more than a single  
               digit of precision will cause truncation at a single digit, for  
               example, if click charge is set to 15.475 and later retrieved with  
               a get, the value will be 15.400 for this object."  
::={ scanned-media-usage 1 }  
                
                
scanned-media-simplex-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Charge for each simplex page printed in this media size."  
::={ scanned-media-usage 2 }  
                
                
scanned-media-duplex-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..930576247)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of duplex pages scanned, for this media size."  
::={ scanned-media-usage 3 }  
                
                
scanned-media-duplex-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Charge for each duplex page scanned, for this media size."  
::={ scanned-media-usage 4 }  
                
                
scanned-media-total-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The total charge for pages scanned, for this media size."  
::={ scanned-media-usage 5 }  
                
                
usage-scanner-total-charge OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total scanner charge or cost for all paper sizes scanned."  
::={ scanner-accounting 2 }  
                
                
printed-media-color-simplex-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of color simplex pages printed in this media		  
               size."  
::={ printed-media-color-usage 1 }  
                
                
printed-media-color-duplex-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of color duplex pages printed in this media size."  
::={ printed-media-color-usage 3 }  
                
                
printed-media-color-total-count OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The total count for color pages printed in this media size."  
::={ printed-media-color-usage 5 }  
                
                
printed-media-color-dimplex-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of color dimplex pages printed in this media size.		  
               A color dimplex page is a color page that has been printed in		  
               duplex mode but the back side is blank. Dimplex pages occur		  
               when the printer firmware inserts a blank page in order to		  
               complete a duplexed job which is sent to the printer with an		  
               odd number of pages."  
::={ printed-media-color-usage 6 }  
                
                
printed-modes-mono-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of mono pages printed in this fuser mode."  
::={ printed-modes-usage 1 }  
                
                
printed-modes-color-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of color pages printed in this fuser mode."  
::={ printed-modes-usage 3 }  
                
                
printed-modes-total-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The total count for pages printed in this fuser mode."  
::={ printed-modes-usage 5 }  
                
                
source-tray-usage-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of pages printed from this source tray.  
               Additional information:  
               This object will track how many images have been printed  
               with the original source tray as one of the following:  
               1.  Tray 1  
               2.  Tray 2  
               3.  Tray 3  
               4.  Tray 4  
               5.  Other"  
::={ source-tray-usage 1 }  
                
                
destination-bin-usage-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of pages printed to this destination bin.  
               Additional information:  
               This object will track how many images have been printed  
               with the original destination bin as one of the following:  
               1.  Face Down Bin  
               2.  External Bin  
               3.  Other"  
::={ destination-bin-usage 1 }  
                
                
media-size-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The number of impressions printed on sheets of this media size.		  
               The device POS should state whether this value is lost across a		  
               power cycle or is kept in permanent storage.  
               Additional information:  
               The value of this object is persistent across a power cycle.    
                 
               The index for these objects, the last number of the OID, uniquely  
               identifies the paper size. This value corresponds to the page sizes listed below.  
               These values are also documented in the PCL Implementor's Guide  
               and the PML Master MIB.    
                 
               1 US-Executive    
               2 US-Letter    
               3 US-Legal    
               11 eLedger    
               15 Statement    
               17 ROC 16K    
               18 JIS Executive    
               19 eROC8K    
               25 ISO and JIS A5    
               26 ISO and JIS A4    
               27 ISO and JIS A3    
               45 JIS B5    
               46 JIS B4    
               65 ISO B5    
               72 eJapanesePostcardDouble      
               80 Monarch    
               81 Commercal-10    
               90 International DL    
               91 International C5    
               100 International B5    
               101 Custom    
               258 eUSLetterR    
               282 ISO JISA4R    
               32767 Unknown Paper Size"  
::={ media-size 1 }  
                
                
printer-average-marking-agent-coverage OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to read the average marking agent coverage		  
               for a given color plane. It is a real number that represents		  
               percentage full and will read from 0 to 100%. This object		  
               obsoletes or replaces USAGE-AVERAGE-TONER-COVERAGE which could		  
               only be used for black toner coverage information.  
               Additional information:  
               The average percent of toner coverage for a specific  
               color plane.  The OID binding is the color plane.  
               Only color planes which the printer supports will be  
               available.  This is only available if a hard disk is  
               installed."  
::={ printer-average 1 }  
                
                
printer-average-marking-agent-coverage-sum OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to read the accumulated sum of the percent		  
               coverage numbers calculated on a per page basis over the life		  
               of the printer.  
               Additional information:  
               The sum of the percent toner coverages for all  
               impressions printed.  The OID binding is the color  
               plane.  Only color planes which the printer supports  
               will be available."  
::={ printer-average 2 }  
                
                
printer-average-marking-agent-coverage-sum-squared OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to read the accumulated sum of the squares		  
               of the percent coverage numbers calculated on a per page basis		  
               over the life of the printer.  
               Additional information:  
               The sum of the percent toner coverages squared for  
               all impressions printed.  The OID binding is the  
               color plane.  Only color planes which the printer  
               supports will be available."  
::={ printer-average 3 }  
                
                
localization-languages-supported OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The list of languages supported by the device. The languages		  
               are primarily, but not limited to, two character codes from ISO		  
               639, each separated by a comma character.  
               Additional information:  
               This string will always be in the Roman-8 character  
               set.  See prtLocalizationLanguage for details about each language value."  
::={ status-system 52 }  
                
                
localization-countries-supported OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The list of countries supported by the device. The countries		  
               are primarily, but not limited to, two character codes from ISO		  
               3166, each separated by a comma character.  
               Additional information:  
               This string will always be in the Roman-8 character  
               set.  See prtLocalizationCountry for details about each country value."  
::={ status-system 53 }  
                
                
control-panel-button-press OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eGoButton(1),  
		  eCancelJobButton(9)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Writing this object simulates pressing a button on the control		  
               panel. Reading it will return the last key pressed either on		  
               the control panel or via PML. The device POS will specify which		  
               keys are supported."  
::={ status-system 60 }  
                
                
control-panel-display-contents-change-counter OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "A counter which increments whenever the contents of the front		  
               panel display changes. This object is implemented as a 32-bit		  
               signed integer which rolls over to zero when it reaches a		  
               maximum value."  
::={ status-system 63 }  
                
                
control-panel-display-contents-crc OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Reading this object returns a 32-bit Cyclical Redundancy Check		  
               (CRC) which represents the current contents of the display.  
               Additional information:  
               This object has been implimented as an 32-bit CRC for  
               this product."  
::={ status-system 64 }  
                
                
control-panel-display-graphical-contents OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Reading this object returns a graphical file format image		  
               representing the current pixel content of the display. The		  
               device POS will specify the expected screen resolution, color		  
               depth of the display and graphics file format for a given		  
               product (eg. 160x64x1 GIF format OR 640x240x4 JPEG format). If		  
               the image is large enough that it needs to be returned in		  
               multiple objects then each array object will contain a portion		  
               of the image. The image will then need to be reconstructed by a		  
               host application. An application that needs to determine if		  
               their is an additional object to be retreived will need to		  
               perform a GETNEXT operation until there are no more objects in		  
               the sub-tree.  
               Additional information:  
               This object returns a GIF image that represents the  
               current contents of the 640x240x2 control panel display.  Most  
               display images require more than one instance of this object  
               in order to retreive the complete GIF image."  
::={ control-panel-display 1 }  
                
                
control-panel-key-press OBJECT-TYPE  
  SYNTAX      INTEGER(0..65535)  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Writing this object simulates pressing a key on the control		  
               panel. Reading it will return the last key pressed either on		  
               the control panel or via PML. This object obsoletes/replaces		  
               CONTROL-PANEL-BUTTON-PRESS object which was unable to represent		  
               each of the possible key combinations of our current control		  
               panels (ie. Full QWERTY keyboard). The device POS will specify		  
               the full range of keys supported by this object.  
               Additional information:  
               >>>>This object is write-only for hw_rom variant but it is  
               read-write for all other variants.<<<<<  
                 
               Writing this object simulates pressing a key on the  
               control panel. Reading it will return the last key pressed  
               either on the control panel or via PML.  This object  
               obsoletes/replaces CONTROL-PANEL-BUTTON-PRESS object which  
               was unable to represent each of the possible key combinations  
               of our current control panels (ie. Full QWERTY keyboard).    
                 
               The device POS will specify the full range of keys supported  
               by this object.  The N$product_strOMI_MFP implementation of this object  
               supports the Unified Key Encoding Scheme which is documented  
               at http://$product_str.boi.hp.com/components/cp/UnifiedKeyEncoding.doc     
                 
               	       "  
::={ status-system 66 }  
                
                
energy-star OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the Energy Star sleep value. If the value		  
               is greater than zero, then the device will go into energy		  
               saving sleep mode after the print engine has been idle for the		  
               number of seconds specified by this object. A value of zero		  
               means Energy Star is disabled and the device will not go to		  
               sleep based on print engine idle time. The value must be		  
               non-negative.  
               Additional information:  
               Returns or changes the Energy Star sleep value.  
               The device will go into energy saving sleep  
               mode after the print engine has been idle for  
               the number of seconds specified by this  
               object.    
                 
               N$product_stromi MFP supports values of 0, 60, 900, 1800, 2700,  
               3600, 5400, 7200, 14400  seconds.  A value of 0 means  
               never enter sleep mode based on the print engine  
               idle time.  Setting to an unsupported value causes  
               the printer to substitute a value (listed  
               below) and to return <noError>  
               status.  Setting this value when the printer is in  
               sleep mode will not cause it to wakeup unless it is  
               set to 0.    
                 
               The values are as follow:    
               <=0                 snap to 0    
               >=1    and <= 479   snap to 60    (1 minute)    
               >=480  and <= 1349  snap to 900   (15 minutes)    
               >=1350 and <= 2249  snap to 1800  (30 minutes)    
               	                >=2250 and <= 3149  snap to 2700  (45 minutes)     
               >=3150 and <= 4499  snap to 3600  (1 hour)    
               >=4500 and <= 6299  snap to 5400  (90 minutes)    
               >=2700 and <= 5399  snap to 3600  (1 hour)    
               >=5400 and <= 10799 snap to 7200  (2 hours)    
               >=10800             snap to 14400 (4 hours)."  
::={ settings-system 1 }  
                
                
sleep-mode OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eFalse(1),  
		  eTrue(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns eTrue if the device is in energy saving sleep mode,		  
               otherwise returns eFalse. Setting SLEEP-MODE to eFalse causes		  
               the device to wake up, if it is in sleep mode. Setting		  
               SLEEP-MODE to eTrue causes the device to go into sleep mode.  
               Additional information:  
               This object returns eTrue if the device is in  
               energy saving sleep mode, otherwise it returns eFalse.    
               Setting this object to eTrue while the printer  
               is awake will not change the printer's current state  
               and will return <genErr>  
               status. NOTE: This object should behave this way  
               when the printer does not have an instant-on fuser.    
               Setting this object to eTrue while printer is already  
               in Sleep Mode will not change the printer's  
               current state and will return <noError> status.    
               Setting this object to eFalse while printer is already  
               awake will not change the printer's current state and  
               will return <noError> status.    
               Setting this object to eFalse while the printer is  
               asleep causes the device to wake up.   "  
::={ settings-system 2 }  
                
                
on-off-line OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOnline(1),  
		  eOffline(2),  
		  eOfflineAtEndOfJob(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "To bring the PDL processing sub-system on or off line. If the		  
               device is a printer, then the printer does not process print		  
               job data when the printer is off line. PML communication		  
               persists.  
               Additional information:  
               When the printer is in the Offline state,  
               printing will stop as soon as possible (no more sheets  
               of media are pulled from input trays).  The I/O  
               is taken offline also.    
                 
               Setting to eOnline has the following affect:  
               Printer will immediately go to or remain in the Online  
               state; <noError> status is returned.    
               If the printer's current state  
               is Offline with a pending error condition that  
               prevents the printer from going to the Online  
               state, the printer will remain in the Offline state;  
               <genErr> status is returned  
                                
               Setting to eOffline has the following affect:  
               Printer will immediately go to or remain in the  
               Offline state; <noError> status is returned.  
               If pages are being printed, those pages will complete  
               with the printer in the Offline state.    
                 
               Setting to eOfflineAtEndOfJob has the following  
               affect:    
               If not in a job or already in the Offline state, the  
               printer will immediately go to or remain in the  
               Offline state; <noError> status is returned.    
               If in a job and the current state is Online, the  
               printer will remain in the Online state, with the  
               value of this object as eOfflineAtEndOfJob, until the  
               end of the job; <noError> status is returned. At the end of  
               the job, the printer goes to the Offline state and the  
               value of this object becomes eOffline.    
               Setting this object to eOffline or eOnline before the  
               end of the job causes the action for that value to be  
               taken immediately."  
::={ status-system 5 }  
                
                
continue OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eInitiateAction(1)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "A device can support a class of errors called continuable		  
               errors. When a continuable error is encountered, the device		  
               requires a continue event to occur before the device will		  
               continue operation. One continue event is setting the CONTINUE		  
               object to eInitiateAction. Devices can support other continue		  
               events, like auto-continue. A continue event causes the		  
               continuable error to be acknowledged, thus allowing the device		  
               to continue. Each device needs to list the continuable errors.		  
               If the device doesn't currently have an unacknowledged		  
               continuable error, the response will contain		  
               <genErr>.  
               Additional information:  
               See the CLEARABLE-WARNING and AUTO-CONTINUE objects for the  
               errors that this object will clear."  
::={ status-system 6 }  
                
                
auto-continue OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Indicates if the device will automatically continue after		  
               encountering a continuable error. If AUTO-CONTINUE is set to		  
               eOn, the device will automatically generate continue event to		  
               acknowledge continuable errors. If AUTO-CONTINUE is set to		  
               eOff, then some other continue event will have to acknowledge		  
               the continuable error.  
               Additional information:  
               If this is set to eOn the device displays an  
               error message and goes offline for ten seconds. After ten seconds the  
               printer automatically returns to the online state.    
                 
               If this is set to eOff then the device displays an error message and  
               goes offline. It remains offline until the operator presses the GO key or  
               until the CONTINUE object is set.    
                 
               If the printer is not idle, the new value may not take effect  
               until a job boundary is reached. If a get is done on this object before  
               the job boundary is reached, the value last set will be returned."  
::={ status-system 7 }  
                
                
simm1-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eUnSupported(3),  
		  eReadOnlyMemory(4),  
		  eVolatileRandomAccessMemory(5),  
		  eFlashMemory(7),  
		  eRamRom(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in SIMM		  
               slot 1.    	  
                   eEmpty means the device did not detect any option installed		  
                       in the interface slot.    	  
                   eUnknown means the device doesn't recognize the installed		  
                       option.    	  
                   eUnSupported means the device recognizes the installed		  
                       option, but does not support the option.    	  
                   eReadOnlyMemory means the installed option contains ROM		  
                       Ics.    	  
                   eVolatileRandomAccessMemory means the installed option		  
                       contains RAM ICs that loose data when the power is		  
                       turned off.    	  
                   eNonVolatileRandomAccessMemory means that the installed		  
                       option contains RAM ICs that do not loose data when the		  
                       power is turned off.    	  
                   eFlashMemory means that the installed option contains a		  
                       type of non-volatile RAM that needs to be erased before		  
                       it can be written.    	  
                   eDiskDrive means the installed option contains a disk		  
                       drive.    	  
                   eRamRom means the installed option contains both volatile		  
                       random access memory and read only memory.    	  
                   eInputPHD means the installed option is an input paper		  
                       handling device.    	  
                   eOutputPHD means the installed option is an output paper		  
                       handling device. eIOCard means the installed option is		  
                       an I/O card.     
               Additional information:  
               This object is used for describing DIMMs instead  
               of SIMMs on $product_str. eRamRom is used to denote $product_str's combo simm."  
::={ simm1 4 }  
                
                
simm1-capacity OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the capacity of the SIMM installed in		  
               SIMM slot 1. The capacity is dependent on the type of option,		  
               as indicated by the SIMM1-TYPE object. This object has no		  
               meaning if the installed option type is eUnknown or		  
               eReadOnlyMemory. This object contains the size, in bytes, if		  
               the installed option type is eVolatileRandomAccessMemory,		  
               eNonVolatileRandomAccessMemory, eFlashMemory, or eDiskDrive. If		  
               the type of the installed option is eRamRom, this object		  
               contains the size, in bytes, of the random access memory. If		  
               the type of the installed option is eInputPHD, the capacity		  
               indicates the number of input trays supported by the installed		  
               option. If the type of the installed option is eOutputPHD, the		  
               capacity indicates the number of output bins supported by the		  
               installed option. If the type of the installed option is		  
               eIOCard, the capacity indicates the number of logical I/O ports		  
               supported by the I/O card.  
               Additional information:  
               Returns an indication of the capacity of the   
               installed option in bytes.  This object is not   
               supported unless the SIMM1-TYPE type is   
               eVolatileRandomAccessMemory, eRamRom, or eFlashMemory.  
               For eRamRom only the size of the Ram portion of the SIMM  
               is returned."  
::={ simm1 5 }  
                
                
simm1-bank1-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eUnSupported(3),  
		  eReadOnlyMemory(4),  
		  eVolatileRandomAccessMemory(5),  
		  eFlashMemory(7),  
		  eRamRom(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in Bank 1		  
               of SIMM slot 1. See SIMM1-TYPE for a description.  
               Additional information:  
               This object is used for describing the type  
               of DIMM banks.  Each physical DIMM slot has up to 2 banks."  
::={ simm1-bank1 1 }  
                
                
simm1-bank1-capacity OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the capacity of Bank 1 of the SIMM		  
               installed in SIMM slot 1. See SIMM1-CAPACITY for a		  
               description.  
               Additional information:  
               Returns an indication of the capacity of the  
               installed bank option in bytes.  This object is not  
               supported unless the SIMM1-BANK1-TYPE type is  
               eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory,  
               eSDRandomAccessMemory, eSRandomAccessMemory,  
               or eFPMRandomAccessMemory."  
::={ simm1-bank1 2 }  
                
                
simm1-bank2-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eUnSupported(3),  
		  eReadOnlyMemory(4),  
		  eVolatileRandomAccessMemory(5),  
		  eFlashMemory(7),  
		  eRamRom(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in Bank 2		  
               of SIMM slot 1. See SIMM1-TYPE for a description.  
               Additional information:  
               This object is used for describing the type  
               of DIMM banks.  Each physical DIMM slot has up to 2 banks."  
::={ simm1-bank2 1 }  
                
                
simm1-bank2-capacity OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the capacity of Bank 2 of the SIMM		  
               installed in SIMM slot 1. See SIMM1-CAPACITY for a		  
               description.  
               Additional information:  
               Returns an indication of the capacity of the  
               installed bank option in bytes.  This object is not  
               supported unless the SIMM1-BANK2-TYPE type is  
               eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory,  
               eSDRandomAccessMemory, eSRandomAccessMemory,  
               or eFPMRandomAccessMemory."  
::={ simm1-bank2 2 }  
                
                
simm2-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eUnSupported(3),  
		  eReadOnlyMemory(4),  
		  eVolatileRandomAccessMemory(5),  
		  eFlashMemory(7),  
		  eRamRom(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in SIMM		  
               slot 2. See SIMM1-TYPE for a description.  
               Additional information:  
               This object is used for describing DIMMs instead  
               of SIMMs on $product_str. eRamRom is used to denote $product_str's combo simm."  
::={ simm2 4 }  
                
                
simm2-capacity OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the capacity of the SIMM installed in		  
               SIMM slot 2. See SIMM1-CAPACITY for a description.  
               Additional information:  
               This object is used for describing DIMMs instead  
               of SIMMs on $product_str. Returns an indication of the capacity of the  
               installed option in bytes.  This object is not  
               supported unless the SIMM2-TYPE type is  
               eVolatileRandomAccessMemory, eRamRom, or eFlashMemory.  
               For eRamRom only the size of the Ram portion of the  
               SIMM is returned."  
::={ simm2 5 }  
                
                
simm2-bank1-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eUnSupported(3),  
		  eReadOnlyMemory(4),  
		  eVolatileRandomAccessMemory(5),  
		  eFlashMemory(7),  
		  eRamRom(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in Bank 1		  
               of SIMM slot 2. See SIMM1-TYPE for a description.  
               Additional information:  
               This object is used for describing the type  
               of DIMM banks.  Each physical DIMM slot has up to 2 banks."  
::={ simm2-bank1 1 }  
                
                
simm2-bank1-capacity OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the capacity of Bank 1 of the SIMM		  
               installed in SIMM slot 2. See SIMM1-CAPACITY for a		  
               description.  
               Additional information:  
               Returns an indication of the capacity of the  
               installed bank option in bytes.  This object is not  
               supported unless the SIMM2-BANK1-TYPE type is  
               eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory,  
               eSDRandomAccessMemory, eSRandomAccessMemory,  
               or eFPMRandomAccessMemory."  
::={ simm2-bank1 2 }  
                
                
simm2-bank2-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eUnSupported(3),  
		  eReadOnlyMemory(4),  
		  eVolatileRandomAccessMemory(5),  
		  eFlashMemory(7),  
		  eRamRom(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in Bank 2		  
               of SIMM slot 2. See SIMM1-TYPE for a description.  
               Additional information:  
               This object is used for describing the type  
               of DIMM banks.  Each physical DIMM slot has up to 2 banks."  
::={ simm2-bank2 1 }  
                
                
simm2-bank2-capacity OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the capacity of Bank 2 of the SIMM		  
               installed in SIMM slot 2. See SIMM1-CAPACITY for a		  
               description.  
               Additional information:  
               Returns an indication of the capacity of the  
               installed bank option in bytes.  This object is not  
               supported unless the SIMM2-BANK2-TYPE type is  
               eReadOnlyMemory, eFlashMemory, eEDORandomAccessMemory,  
               eSDRandomAccessMemory, eSRandomAccessMemory,  
               or eFPMRandomAccessMemory."  
::={ simm2-bank2 2 }  
                
                
cancel-job OBJECT-TYPE  
  SYNTAX      INTEGER(-1..32767)  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Cancels the print job whose ID matches the value written to the		  
               CANCEL-JOB object. The host first learns the job ID using the		  
               CURRENT-JOB-PARSING-ID command. If the printer has completely		  
               processed the job, the printer responds with		  
               <badValue>. If the value of the		  
               CURRENT-JOB-PARSING-ID is smaller than the value written to the		  
               CANCEL-JOB object, then the printer responds with		  
               <badValue>. When read, returns the value		  
               of the last job ID what was canceled, or -1 to indicate no job		  
               has been canceled.  
               Additional information:  
               If the value written matches the ID of a job that is  
               currently being canceled (for any reason),  
               the printer responds with <noError>.    
               It uses job ID's in the range of -1..32767.  
               Because the ID number can wrap to zero,  
               CURRENT-JOB-PARSING-ID may be smaller than the value  
               written to this object; when this occurs, no error  
               will result as long as the ID is for a currently  
               processing job. This object is write only, so the  
               comment in the general description stating the  
               job ID will be returned on a read does not  
               apply. A -1 represents the current job"  
::={ settings-job 2 }  
                
                
os-execute-file OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "This object's input is a null-terminated string representing a		  
               fully-qualified path name for an executable file. This object		  
               causes the file to be executed by the OS.  
               Additional information:  
               This object's input is a null-terminated string of two or  
               more whitespace-separated tokens.  The first token is a path  
               to a directory to make the current working directory.  The  
               second token is a path to an executable file to be executed.  
               Any remaining whitespace-separated tokens are optional and  
               will be passed as parameters to the executable.  The paths   
               to the directory and executable can be either PJL style   
               (e.g., 1:\app\example) or UNIX-style (e.g.,   
               /hpmnt/dsk_ide1a/app/example).  The executable is run in  
               a separate process."  
::={ operating-system 1 }  
                
                
form-feed OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eInitiateAction(1)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Instructs the PDL processing sub-system to finishing processing		  
               the current page of the current job. Form feed is also known as		  
               close page or eject page. If the PDL processing sub-system is		  
               in a FORM-FEED-NEEDED state, this causes the device to flush or		  
               finish processing the current page of the current job. If the		  
               device is not in the FORM-FEED-NEEDED state, an		  
               <genErr> will occur."  
::={ settings-pdl 5 }  
                
                
form-feed-needed OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eFalse(1),  
		  eTrue(2)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates if the PDL processing sub-system has made marks on		  
               the current page and the source subsystem has been idle for a		  
               device specific amount of time.  
               Additional information:  
               $product_str will set this object to eTrue when it  
               has made marks on the current page, the IO-TIMEOUT has  
               expired while PCL was running in `backward-compatibility  
               mode' (which is caused by jobs consisting purely of PCL  
               data with no prepended PJL commands), and no data is pending  
               on another I/O. Once it is set to eTrue, more data on the  
               same I/O will cause this object to be set to eFalse, until  
               the above conditions are met again."  
::={ status-pdl 2 }  
                
                
background-status-msg-higher-priority OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..20))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The string displayed on the device's front panel in place of		  
               the printer's built-in background status string. It would		  
               alternate with warning messages and would overwrite highest		  
               Regular Priority Status message such as PAUSED. The object		  
               could be used to display higher priority third party messages		  
               which are important to be displayed even if printer is offline.		  
               This would not overwrite any HighStatus or Error type message.  
               Additional information:  
               This object allows a message to be displayed when  
               it is the highest priority message. Setting this  
               object does not guarantee the message will be  
               displayed; and reading it returns the value last  
               written, not the currently displayed message (use  
               prtConsoleDisplayBufferText to read the  
               display).    
               The priority assigned for displaying this message  
               is lower than the PAUSED message.  In other words,  
               this messages can replace all the regular priority  
               status messages as EPOffline is the highest regular  
               status priority.    
               To clear the message, write a null string to  
               BACKGROUND-STATUS-MSG-HIGHER-PRIORITY."  
::={ background-message 5 }  
                
                
background-status-msg-line1-part1 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..20))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The string displayed on the device's front panel in place of		  
               the printer's built-in background status string. An example		  
               built-in background status string is '00 READY'.  
               Additional information:  
               The display size for the $product_str printers is 2 X 16.  
               The value of this object and the current value of  
               BACKGROUND-STATUS-MSG-LINE2-PART1 are displayed  
               together on the 2-line display, but they must   
               be set independently.  If line 2 has been set, and the  
               next message to be displayed only requires line 1,  
               BACKGROUND-STATUS-MSG-LINE2-PART1 must be set to the   
               null string to clear it.    
               This object allows a message to be displayed when  
               it is the highest priority message. Setting this  
               object does not guarantee the message will be  
               displayed; and reading it returns the value last  
               written, not the currently displayed message (use  
               prtConsoleDisplayBufferText to read the  
               display).    
               The priority assigned for displaying this message  
               is one lower than the READY message.  In other words,  
               the only message that can be replaced by these  
               objects is the READY message.    
               To clear the message, write a null string to both  
               this object and BACKGROUND-STATUS-MSG-LINE2-PART1."  
::={ background-message1 1 }  
                
                
background-status-msg-line2-part1 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..20))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The string displayed on the device's front panel in place of		  
               the printer's built-in background status string. An example		  
               built-in background status string is '00 READY'.  
               Additional information:  
               See BACKGROUND-STATUS-MSG-LINE1-PART1"  
::={ background-message2 1 }  
                
                
background-status-msg-line3-part1 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..20))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The string displayed on the device's front panel in place of		  
               the printer's built-in background status string. An example		  
               built-in background status string is 'READY'.  
               Additional information:  
               The string displayed on the device's front panel in place of  
               the printer's built-in background status string. An example  
               built-in background status string is 'READY'."  
::={ background-message3 1 }  
                
                
background-status-msg-line4-part1 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..20))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The string displayed on the device's front panel in place of		  
               the printer's built-in background status string. An example		  
               built-in background status string is 'READY'.  
               Additional information:  
               The string displayed on the device's front panel in place of  
               the printer's built-in background status string. An example  
               built-in background status string is 'READY'."  
::={ background-message4 1 }  
                
                
                
                
error-log-clear OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eClearErrorLog(1)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Setting this object clears all the entries in the error log		  
               sub-tree.  
               Additional information:  
               Setting this object removes all errors that have been  
               stored in the printer's non-volatile memory."  
::={ status-system 38 }  
                
                
clearable-warning OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOn(2),  
		  eJob(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or controls how the device will track clearable		  
               warnings. A clearable warning indicates a transient event in		  
               the device. The device will continue after the transient event		  
               occurs. If CLEARABLE-WARNING is eOff, the device does not track		  
               clearable warnings. If CLEARABLE-WARNING is eOn, all clearable		  
               warnings will be tracked until cleared (acknowledged). If		  
               CLEARABLE-WARNING is eJob, a clearable warning generated due to		  
               an event that occurs because of the print job being processed		  
               will be automatically cleared when the device has finished		  
               processing the job. Example clearable warning events include		  
               the device altering resolution or page protection due to memory		  
               constraints. The POS will document what transient events are		  
               treated as clearable warnings.  
               Additional information:  
               If set to eOn, the warning is displayed until the GO key  
               is pressed or the CONTINUE object is set.    
                 
               If set to eJob, the warning is displayed until the end of the job in which  
               it was generated."  
::={ settings-job 1 }  
                
                
error1-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 1		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               This item contains the engine  
               page count when the error occurred.    
                 
               If there is currently no error entry for this object, a '0' will be returned.  
               Note that '0' may also be returned when there is a valid error, but a current  
               page count was unavailable. If ERROR1-CODE object also returns '0', then  
               an error has not yet been logged for this object.  
                 
               See ERROR1-CODE for an explanation of the order used for storing errors."  
::={ error1 1 }  
                
                
error1-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               Returns a device specific error code.  
               If the error code returned is '0', then the printer has not yet logged an  
               error for this object.  
               When the maximum number of errors is reached (30 on LaserJet printers), and  
               a new error occurs, the error in ERROR1-CODE will be replaced by the  
               one in ERROR2-CODE, and so on until the last error object will be given  
               the value of the new error.    
                 
               The error number is returned in the upper 16 bits.  
               If it is 68, 69, 79, or 80, then the sub code is returned in the lower  
               16 bits (eg. 68 001C, where the subcode is already a hexadecimal value).  
               If the error number is any other number, then the 1st sub code (XX)  
               will be in bits 15-8 and the 2nd sub code (YY) will be in bits 7-0 (eg.  
               55.04.02) where XX=04 and YY=02).    
                 
                               
               Example: If the error is 68 001A, then the value returned will be 4456474.    
               To break it down: 4456474 = 0x0044001A    
               The upper 16 bits: 0x0044 = 68    
               The lower 16 bits: 0x001A = 001A  
               Which is the error: 68 001A    
                 
               Example: If the error is 55.04.241, then the error code will be 3605745.    
               To break it down: 3605745 = 0x003704F1    
               The upper 16 bits: 0x0037 = 55    
               The upper byte of the lower 16 bits: 0x04 = 04    
               The lower byte of the lower 16 bits: 0xF1 = 241    
               Which is the error: 55.04.241"  
::={ error1 2 }  
                
                
error1-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               This item contains the date and   
               the time when the error occurred.    
                 
               It returns the date and the time at which the error occured in hexadecimal.  
               For instance, if  date is 2004-Jul-13 and time is 03:15 am   
               when the error was logged, then we get 04 07 0d 03 0f where,  
               04 (hex) - corresponds to the year 2004.  
               07 (hex) - corresponds to month 07  
               0d(hex) - corresponds to date 13  
               03(hex) - corresponds to hour- 03  
               0f(hex) - corresponds to min- 15.    
                 
               If there is currently no error entry , '00 00 00 00 00' will be returned.  
               See ERROR1-CODE for an explanation of the order used for storing errors."  
::={ error1 3 }  
                
                
error2-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 2		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error2 1 }  
                
                
error2-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error2 2 }  
                
                
error2-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error2 3 }  
                
                
error3-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 3		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error3 1 }  
                
                
error3-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error3 2 }  
                
                
error3-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error3 3 }  
                
                
error4-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 4		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error4 1 }  
                
                
error4-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error4 2 }  
                
                
error4-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error4 3 }  
                
                
error5-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 5		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error5 1 }  
                
                
error5-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error5 2 }  
                
                
error5-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error5 3 }  
                
                
error6-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 6		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error6 1 }  
                
                
error6-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error6 2 }  
                
                
error6-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error6 3 }  
                
                
error7-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 7		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error7 1 }  
                
                
error7-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error7 2 }  
                
                
error7-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error7 3 }  
                
                
error8-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 8		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error8 1 }  
                
                
error8-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error8 2 }  
                
                
error8-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error8 3 }  
                
                
error9-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 9		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error9 1 }  
                
                
error9-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error9 2 }  
                
                
error9-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error9 3 }  
                
                
error10-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 10		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error10 1 }  
                
                
error10-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error10 2 }  
                
                
error10-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error10 3 }  
                
                
error11-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 11		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error11 1 }  
                
                
error11-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error11 2 }  
                
                
error11-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error11 3 }  
                
                
error12-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 12		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error12 1 }  
                
                
error12-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error12 2 }  
                
                
error12-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error12 3 }  
                
                
error13-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 13		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error13 1 }  
                
                
error13-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error13 2 }  
                
                
error13-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error13 3 }  
                
                
error14-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 14		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error14 1 }  
                
                
error14-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error14 2 }  
                
                
error14-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error14 3 }  
                
                
error15-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 15		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error15 1 }  
                
                
error15-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error15 2 }  
                
                
error15-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error15 3 }  
                
                
error16-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 16		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error16 1 }  
                
                
error16-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error16 2 }  
                
                
error16-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error16 3 }  
                
                
error17-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 17		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error17 1 }  
                
                
error17-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error17 2 }  
                
                
error17-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error17 3 }  
                
                
error18-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 18		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error18 1 }  
                
                
error18-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error18 2 }  
                
                
error18-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error18 3 }  
                
                
error19-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 19		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error19 1 }  
                
                
error19-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error19 2 }  
                
                
error19-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error19 3 }  
                
                
error20-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 20		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error20 1 }  
                
                
error20-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error20 2 }  
                
                
error20-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error20 3 }  
                
                
error21-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 21		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error21 1 }  
                
                
error21-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error21 2 }  
                
                
error21-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error21 3 }  
                
                
error22-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 22		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error22 1 }  
                
                
error22-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error22 2 }  
                
                
error22-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error22 3 }  
                
                
error23-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 23		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error23 1 }  
                
                
error23-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error23 2 }  
                
                
error23-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error23 3 }  
                
                
error24-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 24		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error24 1 }  
                
                
error24-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error24 2 }  
                
                
error24-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error24 3 }  
                
                
error25-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 25		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error25 1 }  
                
                
error25-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error25 2 }  
                
                
error25-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error25 3 }  
                
                
error26-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 26		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error26 1 }  
                
                
error26-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error26 2 }  
                
                
error26-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error26 3 }  
                
                
error27-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 27		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error27 1 }  
                
                
error27-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error27 2 }  
                
                
error27-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error27 3 }  
                
                
error28-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 28		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error28 1 }  
                
                
error28-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error28 2 }  
                
                
error28-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error28 3 }  
                
                
error29-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 29		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error29 1 }  
                
                
error29-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error29 2 }  
                
                
error29-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error29 3 }  
                
                
error30-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 30		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error30 1 }  
                
                
error30-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error30 2 }  
                
                
error30-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error30 3 }  
                
                
error31-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 31		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error31 1 }  
                
                
error31-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error31 2 }  
                
                
error31-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error31 3 }  
                
                
error32-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 32		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error32 1 }  
                
                
error32-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error32 2 }  
                
                
error32-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error32 3 }  
                
                
error33-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 33		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error33 1 }  
                
                
error33-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error33 2 }  
                
                
error33-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error33 3 }  
                
                
error34-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 34		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error34 1 }  
                
                
error34-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error34 2 }  
                
                
error34-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error34 3 }  
                
                
error35-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 35		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error35 1 }  
                
                
error35-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error35 2 }  
                
                
error35-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error35 3 }  
                
                
error36-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 36		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error36 1 }  
                
                
error36-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error36 2 }  
                
                
error36-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error36 3 }  
                
                
error37-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 37		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error37 1 }  
                
                
error37-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error37 2 }  
                
                
error37-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error37 3 }  
                
                
error38-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 38		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error38 1 }  
                
                
error38-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error38 2 }  
                
                
error38-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error38 3 }  
                
                
error39-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 39		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error39 1 }  
                
                
error39-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error39 2 }  
                
                
error39-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error39 3 }  
                
                
error40-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 40		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error40 1 }  
                
                
error40-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error40 2 }  
                
                
error40-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error40 3 }  
                
                
error41-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 41		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error41 1 }  
                
                
error41-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error41 2 }  
                
                
error41-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error41 3 }  
                
                
error42-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 42		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error42 1 }  
                
                
error42-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error42 2 }  
                
                
error42-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error42 3 }  
                
                
error43-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 43		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error43 1 }  
                
                
error43-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error43 2 }  
                
                
error43-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error43 3 }  
                
                
error44-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 44		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error44 1 }  
                
                
error44-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error44 2 }  
                
                
error44-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error44 3 }  
                
                
error45-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 45		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error45 1 }  
                
                
error45-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error45 2 }  
                
                
error45-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error45 3 }  
                
                
error46-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 46		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error46 1 }  
                
                
error46-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error46 2 }  
                
                
error46-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error46 3 }  
                
                
error47-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 47		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error47 1 }  
                
                
error47-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error47 2 }  
                
                
error47-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error47 3 }  
                
                
error48-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 48		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error48 1 }  
                
                
error48-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error48 2 }  
                
                
error48-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error48 3 }  
                
                
error49-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 49		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error49 1 }  
                
                
error49-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error49 2 }  
                
                
error49-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error49 3 }  
                
                
error50-time-stamp OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains some sort of time stamp indicating when error 50		  
               occurred. Example time stamps include the actual time the error		  
               occurred (in seconds since Jan. 1, 1970), and the total engine		  
               page count. The device POS documents the meaning of the time		  
               stamp.  
               Additional information:  
               See ERROR1-TIME-STAMP."  
::={ error50 1 }  
                
                
error50-code OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains a device specific error code. Each device POS should		  
               list what errors are logged to the error log and the meaning of		  
               each supported error code value.  
               Additional information:  
               See ERROR1-CODE."  
::={ error50 2 }  
                
                
error50-date-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item contains the date and the time at which an error		  
               occurred. The values returned will be in hexadecimal. If the		  
               date is 2004-Jul-13 and the time is 03:15 a.m., we get 04 07 0d		  
               03 0f where,    	  
                   04 (hex) - corresponds to the year 2004.    	  
                   07 (hex) - corresponds to month, 07    	  
                   0d (hex) - corresponds to date, 13    	  
                   03 (hex) - corresponds to hour, 3 a.m.    	  
                   0f (hex) - corresponds to min, 15.     
               Additional information:  
               See ERROR1-DATE-TIME."  
::={ error50 3 }  
                
                
channelprinteralert OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Identifies the values of prtAlertIndex, prtAlertSeverityLevel,		  
               prtAlertGroup, prtAlertGroupIndex, prtAlertLocation, and		  
               prtAlertCode for the latest critical evnet in the		  
               prtAlertTable. The binary string is defined as following:    	  
                   <table>  
                   -----------------------------------------------------  
                   Field  | Filed  | Description   
                   Offset | Length |   
                   -----------------------------------------------------  
                     0    |    4   | the value of prtAlertIndex  
                     4    |    4   | the value of prtAlertSeverityLevel  
                     8    |    4   | the value of prtAlertGroup  
                    12    |    4   | the value of prtAlertGroupIndex  
                    16    |    4   | the value of prtAlertLocation  
                    20    |    4   | the value of prtAlertCode  
                   ------------------------------------------------------  
                   </table>   
                      	  
               Each field is in Big Endian style.  
               Additional information:  
               This object is used to pass alert information from the  
               peripheral to the IIO card.  The standard printer MIB  
               contains the following description:    
                 
               printerAlert TRAP-TYPE    
               ENTERPRISE printerV1Alert    
               VARIABLES { prtAlertIndex, prtAlertSeverityLevel, prtAlertGroup,  
               prtAlertGroupIndex, prtAlertLocation, prtAlertCode }    
               DESCRIPTION    
               'This trap is sent whenever a critical event is added to the  
               prtAlertTable.'    
                 
               In order to provide this information in the trap packet, the  
               IIO card enables traps on channelPrinterAlert.  When a critical  
               alert is generated the peripheral fills the appropriate value  
               into this object and sends it to the card.  
               This object is a structure which contains 24 bytes of data.  
               The structure is:    
                 
               struct structAlertInfo {    
               sint32 prtAlertIndex;    
               sint32 prtAlertSeverityLevel;    
               sint32 prtAlertGroup;    
               sint32 prtAlertGroupIndex;    
               sint32 prtAlertLocation;    
               sint32 prtAlertCode;    
               } thisAlertData;"  
::={ channel 2 }  
                
                
install-date OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(13))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Identifies the date that the device was installed. The format		  
               of the string is 'YYYYMMDDHHmmZ'. Where:    	  
                   YYYY is the year.    	  
                   MM is the month (1-12).    	  
                   DD is the day (1-31).    	  
                   HH is the hour of the day (0-23).    	  
                   mm are the minutes (0-59).    	  
                   'Z' designates Greenwich Mean Time; if 'Z' not specified,		  
                       value is local time.    	  
               Device POS must specify the conditions for setting this		  
               object.  
               Additional information:  
               Setting the <<hidden>> object will  
               enable setting this object."  
::={ status-system 8 }  
                
                
service-id OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(5))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "A read of this object will return the current SERVICE ID value		  
               in the printer. The format is 'YYDDD' where:    	  
                   YY = calendar year - 1990    	  
                   DDD = (calendar month - 1) * 30 + (calendar day of the		  
                       month or 30, if > 30)    	  
               A write of this object will only succeed if the		  
               MANUFACTURING-CONTROL PML object has been set with the correct		  
               <<hidden>>. If the write operation is not allowed, this object		  
               will return an <genErr> status.  
               Additional information:  
               Setting the <<hidden>> object will  
               enable setting this object."  
::={ status-system 19 }  
                
                
show-address OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eAuto(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "If this object is set to eAuto, and the device has an IP		  
               address, the IP address of the device will be shown with the		  
               READY message. If this object is set to eOff, the IP address		  
               will not be shown."  
::={ display-status 3 }  
                
                
serial-number OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..10))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Identifies the serial number for the device. If the		  
               SERIAL-NUMBER object is set by the user, then setting the		  
               object does not need to be protected. If the SERIAL-NUMBER		  
               object is set at the factory, then the <<hidden>> object		  
               must be set correctly before the SERIAL-NUMBER object is		  
               writable. If this is a writable object, the POS should indicate		  
               the maximum supported string length. If possible, encode the		  
               serial number in a symbol set (like Roman-8) that matches the		  
               ASCII character set and limit the characters used to ASCII		  
               characters.  
               Additional information:  
               This value IS AFFECTED BY NVRAM resets, it is set to the   
               default value of XXXXXXXXXX, when a NVRAM init is done."  
::={ id 3 }  
                
                
fw-rom-datecode OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Identifies the base system firmware date code. The date code		  
               will be encoded in the yyyymmdd format. There may be several		  
               versions of the base system firmware. The date code associated		  
               with the version of the base system firmware that is being used		  
               is reported. There may be other date code objects for other		  
               specific modules such as fonts, localization modules, etc.;		  
               these other datecode objects are device specific."  
::={ id 5 }  
                
                
fw-rom-revision OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This identifies the system code firmware ROM revision code. The		  
               format for a revision is major_revision.minor_revision. There		  
               may be other ROM revision code objects for other specific ROMs		  
               such as font ROMs, localization ROMs, etc; these other ROM		  
               revision code objects are device specific."  
::={ id 6 }  
                
                
device-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..32))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "User defined device name. The POS should indicate the maximum		  
               supported string length. If the user entered string is too		  
               long, the device will store as much as possible and will return		  
               the <OKNearestLegal ValueSubstituted>.Additional information:  
               The maximum supported string length is 32    
               characters.  If the user entered string is too long,   
               the device will store the first 32 characters and will   
               return the <noError> status."  
::={ id 10 }  
                
                
device-location OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "User defined device location. The POS should indicate the		  
               maximum supported string length. If the user entered string is		  
               too long, the device will store as much as possible and will		  
               return the <OKNearestLegal ValueSubstituted>.Additional information:  
               The maximum supported string length is 16   
               characters.  If the user entered string is too long,   
               the device will store the first 16 characters and will   
               return the <noError> status."  
::={ id 11 }  
                
                
asset-number OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "User defined asset number. The POS should indicate the maximum		  
               supported string length. If the user entered string is too		  
               long, the device will store as much as possible and will return		  
               the <OKNearestLegal ValueSubstituted>.Additional information:  
               The maximum supported string length is 8   
               characters.  If the user entered string is too long,   
               the device will store the first 8 characters and will    
               return the <noError> status."  
::={ id 12 }  
                
                
ews-request-control-panel-supplies-status OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eFalse(1),  
		  eTrue(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "System variable EWS_REQUEST_CONTROL_PANEL_SUPPPLIES_STATUS		  
               requires a PML interface so that WJA can directly access it		  
               without needing EWS support for that.  
               Additional information:  
               If this object is set to eEnable, the Supplies Status messages will  
               not be shown on the CP."  
::={ settings-web-server 5 }  
                
                
default-copies OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes default copies. Default copies is the		  
               default values used by the PDL to control the number of copies		  
               of each page in the print job that are printed. The print job		  
               can override this value. The list of supported values should be		  
               documented in the device POS.  
               Additional information:  
                The supported values are 1 through 32000.    
               	  Setting to an unsupported value causes the printer to substitute in a snap  
               	  value and to return <noError> status.     
               	  The snaps are as follows:    
               		  <1 snaps to 1    
               		  >999 snaps to 32000"  
::={ settings-pdl 4 }  
                
                
default-lines-per-page OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the default number of lines per page. The		  
               POS indicates the supported values. An unsupported value causes		  
               the printer to use the closest supported value, causing the		  
               printer to return the <noError>.  
               Additional information:  
               The supported values in $product_str are 5 to 128.   
               Setting to an unsupported value causes the    
               the printer to substitute in a snap value and to return   
               <noError>   
               status.     
               The snap values are as follow:     
               <5 snaps to 5     
               >128 snaps to 128"  
::={ settings-pdl 11 }  
                
                
default-vmi OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the default vertical motion index. The unit		  
               of measure for VMI is centipoints per line. The POS indicates		  
               the supported values. An unsupported value causes the printer		  
               to use the closest supported value, causing the printer to		  
               return <noError>."  
::={ settings-pdl 12 }  
                
                
default-media-size OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eFoolscap(10),  
		  eStatement(15),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eJISB5(45),  
		  eJapanesePostcardDouble(72),  
		  eMonarch(80),  
		  eCommercial10(81),  
		  eInternationalDL(90),  
		  eInternationalC5(91),  
		  eInternationalB5(100),  
		  eCustom(101),  
		  eUnknownMediaSize(32767)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This indicates the default media size. A write of an		  
               unsupported value causes an <ErrorInvalidOrUnsupported Value>.		Complete list of supported media sizes along with their		  
               dimensions are listed in the ''Media Size Table'' near the end		  
               of this document. (for a full list of media size enums see the		  
               end of this file) "  
::={ settings-pdl 13 }  
                
                
cold-reset-media-size OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSLetter(2),  
		  eISOandJISA4(26)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the media size that is used as the		  
               DEFAULT-MEDIA-SIZE when a cold reset occurs."  
::={ settings-pdl 19 }  
                
                
reprint OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2),  
		  eAuto(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the reprint (jam recovery) setting. If eOn,		  
               then the device will reprint pages jammed pages. If eOff, the		  
               device will not attempt to reprint jammed pages. If eAuto, a		  
               device dependent algorithm (which should be documented in the		  
               POS) will be used to determine if the page gets reprinted. This		  
               object controls all PDLs, unless a specific PDL supports its		  
               own reprint control mechanism. To date, only PostScript has a		  
               PDL reprint control mechanism."  
::={ settings-pdl 36 }  
                
                
postscript-defer-media OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eDisabled(1),  
		  eEnabled(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object will be used to enable or disable the use of the		  
               Adobe Postscript Paper Handling Model in the printer firmware.		  
               By default it is enabled which means that PostScript will		  
               always defer the media selection to HP Paper Handling Model.  
               Additional information:  
                POSTSCRIPT DEFER MEDIA determines whether ther paper handling  
               model is based on Postscript rules or HP rules.    
               The Values for this item are ENABLED(Follows HP rules) or DISABLED. "  
::={ pdl-postscript 14 }  
                
                
duplex-blank-pages OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eDuplexBlankPagesAuto(1),  
		  eDuplexBlankPagesYes(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "When the value of the system variable is set to		  
               eDuplexBlankPagesAuto, it means to Smart Duplex in any of the		  
               specified conditions. This selection is logically equivalent to		  
               'NO, do not duplex blank pages if not duplexing them obtains a		  
               performance enhancement'. When the value of the system variable		  
               is set to eDuplexBlankPagesYes, it means to disable Smart		  
               Duplexing.  
               Additional information:  
               When the value of the system variable is set to  
               eDuplexBlankPagesAuto, it means to Smart Duplex in any of the  
               specified conditions. This selection is logically equivalent to  
               'NO, do not duplex blank pages if not duplexing them obtains a  
               performance enhancement'. When the value of the system variable  
               is set to eDuplexBlankPagesYes, it means to disable Smart  
               Duplexing."  
::={ settings-prt-eng 28 }  
                
                
tray-prompt OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eDoNotDisplay(1),  
		  eDisplay(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "If this object is set to eDisplay, whenever a paper tray is		  
               opened, refilled, and closed in a printer, the end user is		  
               prompted with a message 'To change size or type press check' on		  
               the control panel. If this object is set to eDoNotDisplay, then		  
               the end user will not be prompted with this message whenever a		  
               paper tray is opened, refilled, and closed in a printer.  
               Additional information:  
               Whenever a paper tray is opened and closed, the user is  
               provided with two options Display and Do Not Display, through  
               the menu item Size/Type Prompt.On selecting Display he chooses  
               to get prompted with the message to change the size or type of  
               paper. Whereas he is not prompted with this message in case he  
               chooses Do Not Display."  
::={ settings-intray 19 }  
                
                
tray-disable-use-instead OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eDisabled(1),  
		  eEnabled(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "If this object is set to eEnabled, the paper mount message that		  
               is normally posted('To use another tray....') is turned off		  
               thereby disallowing the user to specify another tray from which		  
               paper can be taken for printing. However, on setting this		  
               object to eDisabled the paper mount message is posted allowing		  
               the user to specify another tray for paper feed.  
               Additional information:  
               The feature provides a menu item under TRAY BEHAVIOUR, i.e  
               USE ANOTHER TRAY which has two options ENABLED and DISABLED.  
               Whenever the menu item is set to ENABLED, it provides the user  
               with the ability to select another tray from which paper could  
               be provided for the job. However on selecting DISABLED forces  
               the user to provide paper through the same tray, after the paper  
               mount message is posted, in either cases."  
::={ settings-ph 1 }  
                
                
                
                
color-copy-enabled OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEnable(1),  
		  eDisable(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "If this object is set to eEnabled, the MFP allows the user to		  
               make color copies, else mono copies can only be made."  
::={ settings-copier 67 }  
                
                
pcl-total-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of PCL pages printed by the device.  
               Additional information:  
               In $product_str the PCL page count is kept in  
               NVRAM, and the NVRAM value is updated at least every  
               10 pages.  NOTE: The value returned by this object will  
               be incremented every page but if power is lost between  
               NVRAM updates, up to 9 pages of the page count may be  
               lost.  The page count counter will be reset to zero  
               after 16,777,215 (2^24-1) pages.    
               The page count is incremented when a sheet of media is pulled from an input  
               tray. A duplex printed sheet will cause this counter to be incremented by  
               two."  
::={ pdl-pcl 5 }  
                
                
pcl-default-font-height OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the default PCL height. Height is an		  
               approximate measure of the body of the type in centipoints. A		  
               centipoint is 1/7200 inch. Height applies only to proportional		  
               fonts. Point size, in points, can be converted to font height,		  
               in centipoints, by multiplying the point size by 100. The POS		  
               indicates the supported values. An unsupported value causes the		  
               printer to use the closest supported value, causing the printer		  
               to return <noError>. ''Closest'' means		  
               the smallest absolute difference.  
               Additional information:  
               Supported values range from 400 to 99975, in  
               increments of 25 units.  
               Setting to an unsupported value causes the   
               printer to substitute in a snap value and to   
               return <noError> status.     
               The snap values are as follow:     
               <=400 snaps to 400     
               >=99975 snaps to 99975     
               Unsupported values in the range 400 to 99975 snap  
               DOWN to the previous supported value   
               (i.e 25293 snaps to 25275 or 75038 snaps to 75025)."  
::={ pdl-pcl 13 }  
                
                
pcl-default-font-source OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eInternal(1),  
		  ePermanentSoft(2),  
		  eRomSimm2(11),  
		  eRomSimm3(12),  
		  eRomSimm4(13),  
		  eRomSimm5(14)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the value of the default font source		  
               variable in NVRAM."  
::={ pdl-pcl 14 }  
                
                
pcl-default-font-number OBJECT-TYPE  
  SYNTAX      INTEGER(0..255)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the value of the default font number		  
               variable in NVRAM. Writing an unsupported value causes the		  
               printer to generate an <badValue>.  
               Additional information:  
               Valid numbers or 0 - 255, but only font numbers that are   
               included in the PCL FONT LIST are selectable."  
::={ pdl-pcl 15 }  
                
                
pcl-default-font-width OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the default PCL font width. Width is		  
               expressed as the width of a character in centipoints. A		  
               centipoint is 1/7200 inch. Width applies only to fixed space		  
               fonts. Pitch, in character per inch, can be converted to font		  
               width, in centipoints, by dividing 7200 by the pitch. The POS		  
               indicates the supported values. An unsupported value causes the		  
               printer to use the closest supported value, causing the printer		  
               to return <noError>. ''Closest'' means		  
               the smallest absolute difference.  
               Additional information:  
               Setting to an unsupported value causes the   
               printer to substitue in a snap value (listed below)  
               and return <noError> status.     
               The snap values for pitch are as follow:     
               <=44 snaps to 44     
               >=9999 snaps to 9999"  
::={ pdl-pcl 16 }  
                
                
postscript-total-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of PostScript pages printed by the device.  
               Additional information:  
               This object is only supported if the PostScript  
               option is installed.    
               In $product_str the count is kept in NVRAM, and the  
               NVRAM value is updated at least every 10  
               sheets.  NOTE: The value returned by this object will  
               be incremented every sheet but if power is lost between  
               NVRAM updates up to 9 sheets of the count may be  
               lost.  The counter will be reset to zero  
               after 16,777,215 (2^24-1) pages. "  
::={ pdl-postscript 5 }  
                
                
postscript-print-errors OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the value of the print PostScript errors		  
               setting. If eOn, PostScript prints an error page showing the		  
               error encountered and the stack at the time of the error.  
               Additional information:  
               This object is only supported if the PostScript  
               option is installed."  
::={ pdl-postscript 11 }  
                
                
scan-sharpening-coefficient OBJECT-TYPE  
  SYNTAX      INTEGER(0..6)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the sharpening coefficient used in scanning and image		  
               processing. If the device does not support the given value,		  
               then it will select the nearest supported value and return		  
               <noError>. The list of supported values		  
               should be documented in the device POS."  
::={ settings-scanner 15 }  
                
                
scanner-accessory-adf-sheet-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..2147483647)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of sheets that have been fed through the Automatic		  
               Document Feed (ADF) accessory.  
               Additional information:  
               The Automatic Document Feed (ADF) count is  
               incremented each time a sheet feeds through the  
               ADF.  
               The value will be updated at the end of every  
               scan job. "  
::={ settings-scanner 20 }  
                
                
scanner-accessory-flatbed-scan-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..2147483647)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of scans performed by a flatbed scanner		  
               accessory.  
               Additional information:  
               The count is only incremented when a sheet is  
               scanned on the FLATBED.  
               			 The return value of this object will reset  
               to the lower multiple of 10 at a power cycle.  
                 
               		 The value will be updated at the end of every  
               scan job. "  
::={ settings-scanner 21 }  
                
                
scanner-accessory-adf-one-sided-sheet-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item is incremented by 1 for each sheet that is scanned		  
               through the ADF in 1-sided scan mode.  
               Additional information:  
               The value will be updated at the end of every  
               scan job. "  
::={ settings-scanner 59 }  
                
                
scanner-accessory-adf-two-sided-sheet-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item is incremented by 2 for each sheet that is scanned		  
               through the ADF in 2-sided scan mode.  
               Additional information:  
               The value will be updated at the end of every  
               scan job. "  
::={ settings-scanner 60 }  
                
                
scanner-accessory-copy-job-scan-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This relates to the number of pages scanned for copying. This		  
               item is incremented by 2 for each sheet scanned through the ADF		  
               in 2-sided scan mode, and it is incremented by 1 for flatbed		  
               scans. Scanning for testing and calibration purposes are NOT TO		  
               BE INCLUDED in this count.  
               Additional information:  
               The value will be updated at the end of every  
               scan job. "  
::={ settings-scanner 61 }  
                
                
scanner-accessory-send-job-scan-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This relates to the number of pages scanned for fax/send. This		  
               item is incremented by 2 for each sheet scanned through the ADF		  
               in 2-sided scan mode, and it is incremented by 1 for flatbed		  
               scans. Scanning for testing and calibration purposes are NOT TO		  
               BE INCLUDED in this count.  
               Additional information:  
               The value will be updated at the end of every  
               scan job. "  
::={ settings-scanner 62 }  
                
                
scanner-accessory-total-copy-pages-printed OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This relates to the number of copy pages printed on a device.		  
               The output sheet that is duplexed (made 2- sided) should be		  
               counted as 2 pages.  
               Additional information:  
               This relates to the number of copy pages printed on a device.  
               The output sheet that is duplexed (made 2- sided) should be  
               counted as 2 pages."  
::={ settings-scanner 63 }  
                
                
scanner-accessory-digital-send-module-url OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item sets the URL pointer to the Digital Send Module that		  
               is servicing this accessory."  
::={ settings-scanner 64 }  
                
                
scanner-accessory-digital-send-status OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This item is used for detecting the status of the Digital Send		  
               component. A bit-mask indicates the status as follows:    	  
                   0x00 = READY    	  
                   0x01 = DIGITAL_SEND_GATEWAY_DOWN    	  
                   0x02 = SMTP_GATEWAY_DOWN    	  
                   0x04 = LDAP_GATEWAY_DOWN.   "  
::={ settings-scanner 65 }  
                
                
default-scan-original-size OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eFoolscap(10),  
		  eStatement(15),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eJISB5(45),  
		  eUnknownMediaSize(32767)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Contains the default size of the original to be scanned.  
               Additional information:  
               Contains the default size of the original to be scanned.  "  
::={ settings-scanner 66 }  
                
                
default-scan-text-graphics-mix OBJECT-TYPE  
  SYNTAX      INTEGER(0..8)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Contains the mix between graphics and text on the scanned		  
               page."  
::={ settings-scanner 67 }  
                
                
default-scan-job-mode OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Allows user to continue scanning more pages. The UI will prompt		  
               user for more pages if job mode is on."  
::={ settings-scanner 68 }  
                
                
default-scan-background-removal OBJECT-TYPE  
  SYNTAX      INTEGER(0..8)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Background level for background removal.  
               Additional information:  
               Background level for background removal.  "  
::={ settings-scanner 69 }  
                
                
default-scan-image-quality OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNormal(1),  
		  eBest(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Select default image quality.  
               Additional information:  
               Which image quality to use.  "  
::={ settings-scanner 70 }  
                
                
default-scan-content-orientation OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  ePortrait(1),  
		  eLandscape(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Contains the default content orientation for a scanned		  
               document.  
               Additional information:  
               Contains the default content orientation for a scanned  
               document, i.e., the orientation of the page as the user would read it.  "  
::={ settings-scanner 71 }  
                
                
auto-send-reset OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Enables (1) or disables (0) the auto resend timeout.  
               Additional information:  
               Enables (2) or disables (1) the DEFAULT-RESET-SEND-TIMEOUT.  "  
::={ settings-scanner 78 }  
                
                
scanner-accessory-digital-send-log-event-counter OBJECT-TYPE  
  SYNTAX      INTEGER(0..10)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Incremented each time the digital sender writes a log entry.  
               Additional information:  
               Trappable object that is incremented each time the   
               digital sender writes a log entry.  "  
::={ settings-scanner 79 }  
                
                
scanner-accessory-digital-send-config-email-gateway OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..16))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the email gateway address.  
               Additional information:  
               Contains the email gateway address."  
::={ settings-scanner 80 }  
                
                
scanner-accessory-digital-send-config-ldap-gateway OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..16))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the LDAP gateway address.  
               Additional information:  
               Contains the ldap gateway address."  
::={ settings-scanner 81 }  
                
                
scanner-accessory-digital-send-config-dsm-enabled-fax OBJECT-TYPE  
  SYNTAX      INTEGER(0..10)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates if the digital fax service is available.  
               Additional information:  
               Indicates if digital fax service is available."  
::={ settings-scanner 82 }  
                
                
scanner-accessory-digital-send-config-fax-embedded OBJECT-TYPE  
  SYNTAX      INTEGER(0..10)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION " Indicates if the analog fax device is available.  
               Additional information:  
               Indicates if the analog fax (Belin) is available.  "  
::={ settings-scanner 83 }  
                
                
default-scanner-speed OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  e25ppm(1),  
		  e50ppm(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Determines the default scanner speed. (1) is 25 ppm and (2) is		  
               50 ppm.  
               Additional information:  
               Determines the default scanner speed.  (1) is e25 and (2) is e50."  
::={ settings-scanner 88 }  
                
                
scan-to-folder-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..9999999)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The number of scan-to-folder scan jobs.  
               Additional information:  
               The number of scan-to-folder scan jobs."  
::={ settings-scanner 89 }  
                
                
fax-job-scan-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..9999999)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The number of fax scan jobs.  
               Additional information:  
               The number of fax scan jobs."  
::={ settings-scanner 90 }  
                
                
scanner-accessory-digital-send-home-screen-status OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(50))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns a bitmap of enabled, configured, and responding DS		  
               services that indicate what items are present on the Home		  
               Screen.  
               Additional information:  
               Returns a bitmap of enabled, configured, and responding    
               DS services that indicate what items are present on the Home Screen."  
::={ settings-scanner 91 }  
                
                
not-ready-source-scanner OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates whether and why the scanner is not ready. A set bit		  
               indicates a problem.  
               Additional information:  
               This object gives a description of why the scanner is   
               not ready to scan. This value is returned as an integer where each bit            
               represents a reason why the scanner is not ready.  The condition is   
               asserted if the bit is a 1 and deasserted if the bit is a 0.  
               The values are:  
               		Bit 0 - Unknown error.  
               	 	Bit 1 - Invalid media size.  
               		Bit 2 - Scanner feeder open.  
               		Bit 3 - Scanner feeder jam.  
               		Bit 4 - Scanner feeder empty.  
               		Bit 5 - Fatal error.  
               		Bit 6 - Misc. error.  
               		Bit 7 - ADF bin full.  "  
::={ status-scanner 1 }  
                
                
scan-calibration-download OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the state of the calibration operation.    	  
                   cScanCalibrationIdle - This indicates that the device is		  
                                               not currently processing a		  
                       calibration request. The                        host		  
                       should not set the object to this state.		  
                                               SCAN-CALIBRATION-ERROR state		  
                       will reflect results of                         most		  
                       recent calibration.    	  
                   cScanCalibrationActive - The device sets this state to		  
                                              indicate it is in calibration		  
                       mode. The device will set                  		  
                       SCAN-CALIBRATION-ERROR to eNoError(1) as a consequence		  
                                         of entering this state.    	  
                   cScanCalibrationOptical - This state is set by the host to		  
                                               request factory optical		  
                       calibration initiation. The                        		  
                       device should not set to this state. The device will		  
                                               ignore this request, without		  
                       error, if it is already in                         the		  
                       active or the done state.    	  
                   cScanCalibrationADFFaceUpMechanical - This state is set by		  
                       the                         host to request factory		  
                       face up ADF mechanical calibration		  
                                               initiation. The calibration		  
                       target should be placed face up in the ADF.		  
                                               The device should not set to		  
                       this state.                         The device will		  
                       ignore this request, without error, if		  
                                               it is already in the active or		  
                       the done state.    	  
                   cScanCalibrationADFFaceDownMechanical - This state is set		  
                       by the                         host to request factory		  
                       face down ADF mechanical calibration		  
                                               initiation. The calibration		  
                       target should be placed face down in the ADF.		  
                                               The device should not set to		  
                       this state.                         The device will		  
                       ignore this request, without error, if		  
                                              it is already in the active or		  
                       the done state.    	  
                   cScanCalibrationFBMechanical - This state is set by the		  
                                               host to request factory flat		  
                       bed mechanical calibration                        		  
                       initiation. The device should not set to this state.		  
                                               The device will ignore this		  
                       request, without error, if                         it		  
                       is already in the active state.    	  
                   cScanCalibrationADFResetMechanical - This state is set by		  
                       the                         host if he wants to start		  
                       ADF mechanical calibration                         all		  
                       over again. If this is set then both Face Up and Face		  
                       Down                         calibration can be started		  
                       even after a successful pass.    	  
               The device will NOT print a calibration graph when calibration		  
               is complete.  
               Additional information:  
               Returns or changes the state of the calibration operation.  
               cScanCalibrationIdle - indicates that the device is not currently     
               	processing a calibration request. The host should not set the object to this     
               	state. SCAN-CALIBRATION-ERROR state will reflect results of most recent     
               	calibration.  
               cScanCalibrationStart  This state is set by host to request factory \  
               	mechanical calibration initiation. Device should not set to this state. The     
               	device will ignore this request, without error, if it is already in the Active     
               	or the Done state.  
               CScanFactoryCalibrationStart - This state is set by host to request     
               	factory optical calibration initiation. This is the old method and will not be     
               	used on Laserjet 4300 MFP.  
               cScanCalibrationActive  The device sets this state to indicate it is \  
               	in calibration mode. The device will set SCAN-CALIBRATION-ERROR to eNoError(1)     
               	as a consequence of entering this state.  
               cScanCalibrationAborted  Not used.  
               cScanCalibrationDone  The device sets to this state when it has    
               	successfully completed a calibration. The device will update SCAN-CALIBRATION-ERROR     
               	object before entering this state. The device will exit from this state to     
               	cScanCalibrationIdle when it is ready to process another cScanCalibrationStart request.  
               	cScanCalibrationOptical - This state is set by host to request factory optical     
               	calibration initiation. Device should not set to this state. The device will ignore     
               	 this request, without error, if it is already in the Active or the Done state.  
               	cScanCalibrationADFMechanical - This state is set by host to request factory ADF     
               	mechanical calibration initiation. Device should not set to this state. The device will    
               	 ignore this request, without error, if it is already in the Active or the Done state.  
               	cScanCalibrationFBMechanical - This state is set by host to request factory flat bed     
               	mechanical calibration initiation. Device should not set to this state. The device will     
               	ignore this request, without error, if it is already in the Active or the Done state.  
                 
               	The device will NOT print a calibration graph when calibration is complete. "  
::={ status-scanner 5 }  
                
                
scan-calibration-error OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNoError(1),  
		  eUnknownCalibrationError(2),  
		  eScannerFeederEmpty(3),  
		  eLowMemory(4),  
		  eWriteFailed(5),  
		  eScannerBusy(6),  
		  eADFMispick(7),  
		  eADFJam(8),  
		  eUncorrectablePixels(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Error status of the most recent calibration session.    	  
                   eNoError(1) - The calibation was successful.    	  
                   eUnknownCalibrationError(2) - An unknown error occurred.   	                           
                   eScannerFeederEmpty(3) - The feeder contained nothing to		  
                       scan.    	  
                   eLowMemory(4) - Insufficient memory available to complete		  
                       the calibration.    	  
                   eWriteFailed(5) - Write to NVRAM failure.    	  
                   eScannerBusy(6) - Scanner is busy.    	  
               Detailed information about the cause and remedy for each error		  
               should be documented in the device POS.  
               Additional information:  
                Error status of the most recent calibration session.     
               	Only eNoError, eScannerBusy, and eUncorrectablePixels will be supported.     
               	The device will use eScannerBusy to indicate the calibration request occurred     
               	during a time that the device was not ready to perform calibration. The device     
               	will use eUncorrectablePixels to indicate that at least one pixel was not     
               	correctable on at least one of scanning sensors in the device (ADF or flatbed)."  
::={ status-scanner 6 }  
                
                
default-audible-feedback OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the audible feedback function. The default		  
               value will be documented in the device POS.  
               Additional information:  
               Turns the audible feedback function on or off"  
::={ settings-prt-eng 14 }  
                
                
default-reset-send-timeout OBJECT-TYPE  
  SYNTAX      INTEGER(10000..300000)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the period of time, specified in milliseconds,		  
               to wait before the digital send settings are reset to default		  
               values. The default will be specified in the device POS.  
               Additional information:  
               Contains the period, in milliseconds, of inactivity on  
               the control panel before the digital send settings are reset to  
               their default values.  "  
::={ settings-prt-eng 15 }  
                
                
default-authentication-timeout OBJECT-TYPE  
  SYNTAX      INTEGER(0..300000)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the period of time, specified in milliseconds,		  
               to wait before an authentication becomes invalid. The default		  
               will be specified in the device POS.  
               Additional information:  
               Contains the period, in milliseconds, of inactivity on the  
               control panel before the authentication becomes invalid.  "  
::={ settings-prt-eng 16 }  
                
                
default-staple-mode OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNone(1),  
		  eNormal(2),  
		  eAngled(3),  
		  eTwoStaples(4),  
		  eThreeStaples(5),  
		  eSixStaples(6),  
		  eCustomStapleMode(7),  
		  eOppositeCorner(8),  
		  eSaddleStitch(9)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the default staple mode. The device POS will		  
               specify the default and supported values.  
               Additional information:  
               Selects staple mode.  "  
::={ settings-prt-eng 17 }  
                
                
default-mfp-color-space OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eBiLevel(1),  
		  eGray(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Which color space to use  CMY for color, Subtractive Gray for		  
               mono.  
               Additional information:  
               Which color space to use- CMY for color, Subtractive Gray for mono.  "  
::={ imaging 10 }  
                
                
default-copier-media-size OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eFoolscap(10),  
		  eStatement(15),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eJISB5(45),  
		  eJapansePostcardDouble(72),  
		  eCommercial10(81),  
		  eMonarch(80),  
		  eInternationalDL(90),  
		  eInternationalC5(91),  
		  eInternationalB5(100),  
		  eUnknownMediaSize(32767)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the default copy paper size. The device will scan and		  
               format the print data based on the value of this object. The		  
               device behavior when the scanned media or print media does not		  
               match the value of this object should be documented in the		  
               device POS. (for a full list of media size enums see the end of		  
               this file) "  
::={ settings-copier 9 }  
                
                
default-copier-image-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eText(1),  
		  eGraphic(2),  
		  eMixed(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Specifies the dither matrix used when performing a copy		  
               operation."  
::={ settings-copier 10 }  
                
                
copier-media-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eCopierMediaTypePlain(1),  
		  eCopierMediaTypeBrightWhite(2),  
		  eCopierMediaTypePhoto(3),  
		  eCopierMediaTypeSpecial(4),  
		  eCopierMediaTypeTransparency(5),  
		  eCopierMediaTypeIronon(6),  
		  eCopierMediaTypeFastTransparency(7),  
		  eCopierMediaTypeBochureMatte(8),  
		  eCopierMediaTypeBrochureGlossy(9),  
		  eCopierMediaTypePhotoGlossy(10),  
		  eCopierMediaTypePhotoMatte(11),  
		  eCopierMediaTypeEverydayPhoto(12),  
		  eCopierMediaTypePhotoQualInkjet(13),  
		  eCopierMediaTypeOtherPhoto(14),  
		  eCopierMediaTypeAutomatic(15),  
		  eCopierMediaTypeAdvancedPhoto(16),  
		  eCopierMediaTypeIronOnMirrored(17),  
		  eMediaTypeLight(21),  
		  eMediaTypeEnvelope(22),  
		  eHeavyGloss(23),  
		  eGlossFilm(24),  
		  eNonHPHeavyGloss(25)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the copier media type. This value is stored in		  
               NVRAM, hence the value is saved over power cycles.  
               Additional information:  
               Returns or sets the copier media type. This value is stored in  
               NVRAM, hence the value is saved over power cycles."  
::={ settings-copier 14 }  
                
                
default-copy-duplex-mode OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eSimplexToSimplex(1),  
		  eSimplexToDuplex(2),  
		  eDuplexToSimplex(4),  
		  eDuplexToDuplex(5)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the duplex copying mode. Duplex printing is		  
               when printing occurs on both sides of a sheet of media. Long		  
               edge binding is also called vertical binding or book binding.		  
               Short edge binding is also called horizontal binding or		  
               calendar binding.   	  
                   eSimplexToSimplex: takes image data from only one side of		  
                       the original document, and print only on one side of		  
                       each copy.    	  
                   eSimplexToDuplexLongEdgeBinding: takes image data from only		  
                       one side of the original document, and print to both		  
                       sides of each copy. The images are rotated so that if		  
                       the media is rotated along the axis of the long edge of		  
                       the media, both images would appear as in the original.		  
                          	  
                   eSimplexToDuplexShortEdgeBinding: takes image data from		  
                       only one side of the original document, and print to		  
                       both sides of each copy. The images are rotated so that		  
                       if the media is rotated along the axis of the short		  
                       edge of the media, both images would appear as in the		  
                       original.    	  
                   eDuplexToDuplex: takes image data from both sides of the		  
                       original document, and print on both sides of each		  
                       copy.    	  
                   eDuplexToSimplexLongEdgeBinding: takes image data from both		  
                       sides of the original document, and prints to only one		  
                       side of each copy. The images are rotated so that if		  
                       the media is rotated along the axis of the long edge of		  
                       the media, both images would appear as in the original.		  
                          	  
                   eDuplexToSimplexShortEdgeBinding: takes image data from		  
                       both sides of the original document, and prints to only		  
                       one side of each copy. The images are rotated so that		  
                       if the media is rotated along the axis of the short		  
                       edge of the media, both images would appear as in the		  
                       original.     
               Additional information:  
               "  
::={ settings-copier 28 }  
                
                
default-copy-input-tray OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eInTray1(1),  
		  eInTray2(2),  
		  eInTray3(3),  
		  eInTray4(4)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This describes the default input tray to be used. The		  
               correspondence between enumerated values and actual trays is		  
               device defined (and device dependent). The supported writable		  
               enumerated values are device specific."  
::={ settings-copier 29 }  
                
                
default-copy-output-bin OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOutBin1(1),  
		  eOutBin2(2),  
		  eOutBin3(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This describes the default output bin to be used. The		  
               correspondence between enumerated values and actual bins is		  
               device defined (and device dependent). The supported writable		  
               enumerated values are device specific."  
::={ settings-copier 30 }  
                
                
default-copy-reset-timeout OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The time, in seconds, that the printer will wait before		  
               automatically reverting to default copy settings.  
               Additional information:  
               This value is saved over a powercycle."  
::={ settings-copier 31 }  
                
                
default-copier-quantity OBJECT-TYPE  
  SYNTAX      INTEGER(1..999)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This item configures the default copy quantity.  
               Additional information:  
               This value is saved over a powercycle."  
::={ settings-copier 32 }  
                
                
default-copier-flip-pages-up OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eFalse(1),  
		  eTrue(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This item configures the default for the copy 'flip-pages-up'		  
               status."  
::={ settings-copier 33 }  
                
                
default-copier-pages-per-sheet OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNone(1),  
		  eTwoUp(6),  
		  eFourUpNOrder(7),  
		  eFourUpZOrder(8)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Selects a special digital copier mode as follows:    	  
                   eNone: This is the normal copy mode, which means none of		  
                       the special features are in effect.    	  
                   eTwoUp : Scans in 2 pages and produces 2 rotated images on		  
                       a single output page.    	  
                   eFourUpNOrder : Scans in 4 pages and produces 4 scaled down		  
                       images on a single output page. Images are placed in		  
                       top down, left to right order.    	  
                   eFourUpZOrder : Scans in 4 pages and produces 4 scaled down		  
                       images on a single output page. Images are placed in		  
                       left to right, top down order.   "  
::={ settings-copier 34 }  
                
                
default-copier-page-borders OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNone(1),  
		  eLine(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Selects a page boarder mode as follows:   	  
                   eNone : This is the normal copy mode, which no boarder is		  
                       drawn.    	  
                   eLine : A simple border box is drawn around each scanned		  
                       image.   "  
::={ settings-copier 35 }  
                
                
default-copier-collate OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eCollate(1),  
		  eUncollate(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This describes the default setting used to stack the output of		  
               a set of copies.    	  
                   eCollate : Copies are stacked 1st page of 1st copy, 2nd		  
                       page of 1st copy, 3rd page of 1st copy, etc.    	  
                   eUncollate: Copies are stacked 1st page of 1st copy, 1st		  
                       page of 2nd copy, 1st page of 3rd copy, etc.   "  
::={ settings-copier 36 }  
                
                
default-copier-contrast OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This item configures the default Intensity		  
               (brightness/contrast) setting. The number of discrete units		  
               should be application dependent."  
::={ settings-copier 37 }  
                
                
default-copier-edge-to-edge OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNone(1),  
		  eScale(2),  
		  eClip(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This item configures the default edge-to-edge setting for copy		  
               jobs."  
::={ settings-copier 38 }  
                
                
copy-job-scan-ahead OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "When eOn, this implements the 'no-wait scanning' feature.		  
               Originals are scanned to disk while waiting for the printer to		  
               become available. Default is eOn."  
::={ settings-copier 39 }  
                
                
copy-job-auto-interrupt OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "When eOn, a walk-up job will automatically interrupt an		  
               already-printing mopy jobat a mopy boundary. Default is eOff."  
::={ settings-copier 40 }  
                
                
copy-job-interrupt-copy-jobs OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "When eOn, this prompts the user whether to interrupt an		  
               already-printing copy job when a new copy job is started.		  
               Default is eOff."  
::={ settings-copier 41 }  
                
                
copy-job-hold-off-print-jobs OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Controls whether new or pending print jobs can begin while a		  
               walk-up user is setting up a job. That is, for copy jobs and		  
               scan jobs, when eOn this prevents print jobs from starting		  
               while a walk-up user is setting up a job. Default is eOn."  
::={ settings-copier 42 }  
                
                
copy-job-hold-time OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Prevents non-copy print jobs from starting for specified		  
               interval after copy job is completely printed. Defined in		  
               seconds."  
::={ settings-copier 43 }  
                
                
default-copy-job-chromaticity OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eMono(1),  
		  eColor(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Determines the default copy job color setting. eMono(1) is mono		  
               and eColor(2) is color.  
               Additional information:  
               Determines the default copy job color setting. eMono(1) is mono    
               	and eColor(2) is color. This PML id is obsolete and this is a redundant to default-mfp-color-space"  
::={ settings-copier 58 }  
                
                
first-copy-speed OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNoEarlyWarmup(1),  
		  eEarlyWarmup(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This describes the warm-up mode used for the first copy    	  
                   eNoEarlyWarmup: With this the fast first copy feature is		  
                       disabled.    	  
                   eEarlyWarmup: Early warm up is present and fast first copy		  
                       is enabled.     
               Additional information:  
               This describes the warm-up mode used for the first copy     
               eNoEarlyWarmup: With this the fast first copy feature is  
               disabled.     
               eEarlyWarmup: Early warm up is present and fast first copy  
               is enabled.   "  
::={ settings-copier 59 }  
                
                
copier-job-border-setting OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eWithBorders(1),  
		  eWithoutBorders(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Specifies whether the next copier job shall be printed to the		  
               edges of the paper.    	  
                   eWithBorder: Image output shall maintain a unprinted		  
                       border.    	  
                   eBorderless : Image output shall print to the edges of the		  
                       media.     
               Additional information:  
               Specifies whether the next copier job shall be printed to the  
               edges of the paper.     
               eWithBorder: Image output shall maintain a unprinted  
               border.     
               eBorderless : Image output shall print to the edges of the  
               media.   "  
::={ settings-copier 60 }  
                
                
collated-originals-support OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates that the printer can create multiple, collated		  
               'originals' of a job and shows the level of support for this		  
               capability.    	  
                   cCollatedOriginals - The printer can create multiple		  
                       collated originals, or 'mopies'. This is the base		  
                       functionality required by the other collection items.		  
                          	  
                   cProofAndHold - The printer saves a copy of the job while		  
                       printing the first mopy. Later, this held job can be		  
                       released and the rest of the mopies will print.    	  
                   cSecurityPrint - The printer spools the job and holds the		  
                       job until the user releases the job by entering a		  
                       <<hidden>> at the printer's control panel.    	  
                   cAutoHighlight - The printer prints the job a number of		  
                       times with a mail distribution list prepended to each		  
                       job. A different mailing address is highlighted on each		  
                       mopy.    	  
                   cCollatedAtSpeed - The printer can create multiple collated		  
                       copies where all copies after the original are printed		  
                       at engine speed.     
               Additional information:  
               Indicates that the printer can create multiple, collated     
               originals of a job and shows the level of support for this    
               capability.      
               cCollatedOriginals - The printer can create multiple collated    
               originals, or mopies.    
                 
               This is the base functionality required by the other     
               collection items.      
               Without disk, this object will not exist. This will be set at     
               boot-up initialization. If the disk fails, in any way, then     
               the disk error functionality will handle the situation.  
                 
               A color printer (LaserJet 4550) that only has a RAMDISK installed is   
               treated like there is no disk and therefore this object will   
               not exist.    
                 
               The value of this object will be:  
               !cCollatedOriginals - Only FLASH installed  
               cCollatedOriginals  - IDE is installed combined  
               with/without FLASH  
               cCollatedOriginals  - RAMDISK is On combined with/without FLASH"  
::={ status-system 42 }  
                
                
host-application-available-memory OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the amount of memory, in bytes, that the device has		  
               available for job-related processing or resources. Also known		  
               as driver work space (DWS) memory."  
::={ status-system 59 }  
                
                
socket-ping-job-events-version OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..10))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object reports the current version of the Socket Ping Job		  
               Events capability. The version number is returned as a string		  
               in the format MAJOR.MINOR.SUB version. (eg. 1.0.1) If socket		  
               ping is not supported by this printer then the object is either		  
               not implemented or it returns a '0'."  
::={ socket-ping 1 }  
                
                
job-info-change-id OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(16))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the current value of an object in the job-info sub-tree		  
               whose value has changed. Define the object identifier for the		  
               object whose value has changed as		  
               job-info.required-field.optional-field.job-id. job-info		  
               represents the OID prefix of all objects in the job-info		  
               sub-tree. Required-field represents the OID field value that		  
               follows the job-info prefix. Since some objects in the job-info		  
               sub-tree have two OID fields between the job-info prefix and		  
               the job-id, the optional-field represents the OID field between		  
               the required-field and the job-id field, if present. Using this		  
               definition, the format for the JOB-INFO-CHANGE-ID binary value		  
               can be described as follows:    	  
                   Bytes 0-3 : required-field    	  
                   Bytes 4-7 : optional-field, or all zeros if there    	  
                   is no optional field    	  
                   Bytes 8-11: Job ID.    	  
                   Bytes 12-n : The value of the object job-info.		  
                       required-field.optional-field.job-id.    	  
               All multi-byte values stored in Motorola (big-endian) format,		  
               where the most significant byte occurs first.  
               Additional information:  
               $product_str will use this object to report  
               changes to the job-info-pages-printed and job-info-state  
               objects.  The required-field (bytes 0 through 3) will   
               designate whether the change to be reported involves the   
               pages printed (13) or job state (15).  The optional-field   
               (bytes 4 through 7) will always be zeroes.  The value-field  
               (bytes 12 through 15) will contain the new value for pages  
               printed or job state cast to a 32-bit integer.  
                 
               Note:  It is possible that traps generated by this object  
               have the same value.  This is caused by the architecture of  
               $product_str.  In the $product_str System, it is highly probable that  
               the object value will change so rapidly that when the trap is  
               processed, PML will read the same value twice.  This is timing  
               related and will generally be seen at the end of a job."  
::={ settings-job 3 }  
                
                
hold-job-timeout OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The time, in minutes, that the printer will wait before		  
               automatically deleting a held job. This allows the printer to		  
               automatically clean up jobs that have been forgotten (held but		  
               never released).  
               Additional information:  
               This only applies to temporary held jobs, i.e., HOLD=ON or  
               PROOF.  This is a global timer that only affects the jobs  
               that are sent after it is set.  
               		A value of 0 means never delete the jobs.  
               		Setting it to an unsupported value causes  
               		the printer to substitute a value (listed  
               		below) and to return <noError>  
               		status.    
               		LaserJet 4600 supports values of 0, 60, 240, 1440, and 10080     
               		The values are as follows:    
               <=0 snap to 0   (disabled)    
               >=1 and <=150 snap to 60 (60 minutes)    
               >=151 and <=840 snap to 240 (4 hours)    
               >=841 and <=2880 snap to 1440 (1 day)    
               >=2881 snap to 10080  (1 week)"  
::={ settings-job 10 }  
                
                
current-job-parsing-id OBJECT-TYPE  
  SYNTAX      INTEGER(-1..2147483647)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the printer assigned job identification for the job		  
               currently being processed by the processing PDL sub-system. The		  
               job ID is a monotonically increasing number. The job ID may be		  
               reset to zero at power-up and may roll over to zero after		  
               reaching some maximum value.  
               Additional information:  
               A value of -1 is returned when the printer  
               is not parsing a job.    
                 
               When data for a new job is detected, this object is  
               updated (the job may or may not turn out to be a Null  
               Job); however, the trap does not occur until the printer  
               determines that it is not a Null Job.  (A job is considered  
               to be a 'null job' if it has no name or job attribute,   
               causes no pages to be printed, and consumes MIN_JOB_SIZE  
               (9) or fewer bytes.)  A trapped value will differ from   
               the previous value by one or more.  
			   
               Some job-info- objects are created when the first data  
               bytes are received.  If the printer determines that the  
               job is a Null Job, the job-info- objects related to the  
               Null Job are deleted.  $product_str retains the job-info-  
               objects for the MAX_JOBS_IN_LIST (32) most recent jobs   
               that are not Null Jobs.    
                 
               The first job received after power-up will have job ID 1,  
               and the job ID will increment to 2,147,483,647 before   
               rolling to zero.  To distinguish whether a power cycle or a   
               rollover causes a reduction in the job ID value, the   
               object prtGeneralConfigChanges can be watched and if it   
               increments at the same time as the drop is observed in  
               the value of CURRENT-JOB-PARSING-ID, then a power cycle  
               is the most likely cause."  
::={ job-being-parsed 1 }  
                
                
job-info-name1 OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the first part of this print job's name. The last OID		  
               field for this dynamic object contains the job ID.  
               Additional information:  
               The job name is the string specified by the  
               NAME= parameter of the @PJL JOB command which allows a  
               maximum of 80 characters.  The first 40 characters are  
               in this object and the second 40 are in job-info-name2.  
               The symbol set is Roman-8.    
                 
               When jobs are nested, the value assigned to this object  
               is the name provided by the most recent @PJL JOB NAME=  
               command.  If no name is provided, a null string is  
               returned."  
::={ job-info 1 }  
                
                
job-info-name2 OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the second part of this print job's name. The last OID		  
               field for this dynamic object contains the job ID.  
               Additional information:  
               See job-info-name1."  
::={ job-info 2 }  
                
                
job-info-stage OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates what printer sub-systems are currently processing		  
               this print job. The last OID field for this dynamic object		  
               contains the job ID. cSourceSubsystem - some of the job is in		  
               the printer I/O subsystem. cProcessingSubsystem - some of the		  
               job is in the printer imaging processing subsystem.		  
               cDestinationSubsystem - some of the job is being printed.  
               Additional information:  
               For $product_str, cSourceSubsystem and  
               cProcessingSubsystem will always be set and cleared  
               together.  They are set when the beginning of the  
               job is detected, and they are cleared when the end  
               of the job is parsed.    
                 
               A non-printing job will never set  
               cDestinationSubsystem.    
                 
               When a page is ready to be printed (the intermediate has  
               been built and the page is `closed' by the personality),   
               cDestinationSubsystem will be set even if a page of a   
               previous job is currently being printed.  
               cDestinationSubsystem remains set until the last page of  
               the job has finished printing.    
                 
               If a page requires extensive processing and allows all  
               the previous pages of a job to complete printing,  
               cDestinationSubsystem will remain set until the last  
               page of the job has finished printing."  
::={ job-info 10 }  
                
                
job-info-io-source OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates which I/O source, the print job was received over.		  
               The value maps to port numbering scheme supported in the		  
               DEVICE/SOURCE-SUBSYSTEM/IO/PORTS sub-tree."  
::={ job-info 11 }  
                
                
job-info-pages-processed OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates the number of pages processed by the processing		  
               subsystem. If neither the cSourceSubsystem or the		  
               cProcessingSubsystem items are in the associated JOB-INFO-STAGE		  
               object, then this object contains the total number of pages		  
               processed for this job. The last OID field for this dynamic		  
               object contains the job ID.  
               Additional information:  
               This object is incremented by one when a  
               page is processed (`closed' by the personality), regardless   
               of the number of pages that are printed as a result of the   
               single page processed.  In other words, it does not matter   
               how many identical copies of a page are printed or no pages  
               may be printed if operating in silent run mode, this count  
               is incremented exactly once.    
                 
               A page is considered processed when all of the input  
               data has been processed for a page (that is, when the   
               intermediate has been produced, and the personality has   
               `closed' the page.  At this time, the image of the page is   
               not necessarily completely formed.)"  
::={ job-info 12 }  
                
                
job-info-pages-printed OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates the number of pages printed by the destination		  
               subsystem. If none of the cSourceSubsystem,		  
               cProcessingSubsystem or cDestinationSubsystem items are in the		  
               associated JOB-INFO-STAGE object, then this object contains the		  
               total number of pages printed for this job. This value may		  
               increase by two each time for duplex jobs. The last OID field		  
               for this dynamic object contains the job ID.  
               Additional information:  
               If multiple copies of a page are printed,  
               each copy is counted individually."  
::={ job-info 13 }  
                
                
job-info-size OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates the number of bytes of data processed by the		  
               processing subsystem. If neither of the cSourceSubsystem or		  
               cProcessingSubsystem items are in the associated JOB-INFO-STAGE		  
               object, then this object contains the size of this job, in		  
               bytes. The last OID field for this dynamic object contains the		  
               job ID.  
               Additional information:  
               This count may be incremented by values  
               other than one as blocks of data are processed; blocks  
               of data (which may be as large as 2K bytes) will be  
               processed in a varying amount of time.    
                 
               During the processing of a job and even when a job completes,   
               an exact count of the number of I/O bytes processed by the  
               job is not necessarily to be expected."  
::={ job-info 14 }  
                
                
job-info-state OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eAborted(3),  
		  eWaitingForResources(4),  
		  ePrinted(5),  
		  eTerminating(7),  
		  eCancelled(10),  
		  eProcessing(11),  
		  eScanning(12),  
		  eSending(13)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates the state of the job. The last OID field for this		  
               dynamic object contains the job ID.    	  
                   eAborted - the print job was aborted.    	  
                   eWaitingForResources - the print job requires resources		  
                       that are not currently available. Example resources		  
                       that can cause the job to wait include the print engine		  
                       or PDL processor being unavailable. The print engine		  
                       could be unavailable due to paper out, paper jam,		  
                       staple out, stapler jam, marking agent low, output bin		  
                       full, etc. The PDL processor could be unavailable due		  
                       to an off-line condition. Each printer specific object		  
                       specification should state which conditions cause a job		  
                       to be waiting for resources and also state which		  
                       objects can be retrieved by an application to determine		  
                       the exact cause of a resource being unavailable.    	  
                   ePrinted - the job has printed. The related JOB-INFO-		  
                       OUTCOME object indicates if any problems were		  
                       encountered while the job was processed.    	  
                   eRetained - the job can be reprinted.    	  
                   eTerminating - the job was aborted or cancelled and is		  
                       currently is terminating.    	  
                   eInterrupted - the job has been interrupted. The job can be		  
                       continued.    	  
                   ePaused - the job has been paused. The job can be		  
                       continuted.    	  
                   eCancelled - the job has been cancelled.    	  
                   eProcessing - the job is currently being printed normally.		  
                         "  
::={ job-info 15 }  
                
                
job-info-outcome OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOk(3)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates if any warning or error conditions were encountered		  
               while processing the assoicated job. The last OID field for		  
               this dynamic object contains the job ID.  
               Additional information:  
               In $product_str, warnings and errors are not recorded  
               in this object.  Although no meaningful information can be  
               obtained from this object, it is kept around for the  
               compatibility needs of existing software."  
::={ job-info 19 }  
                
                
job-info-outbins-used OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates which output bins this job has delivered printed		  
               pages to. The last OID field for this dynamic object contains		  
               the job ID.  
               Additional information:  
               The bins designated by this collection include  
               the printer's own output bins as well as the `logical output  
               bins' associated with any attached external paper handling  
               devices.  (The mapping of the physical output bins of an  
               external paper handling device to its `logical output bins'  
               depends on the usage mode of the device.  For instance, in  
               `mailbox mode', there is one-to-one correspondence of  
               `logical output bins' to physical bins, whereas in `stacker  
               mode', one `logical output bin' may map to several physical  
               bins.)    
                 
               Although LaserJet 4100 and LaserJet 4550 both come with two output  
               bins -- a face-down bin on the top of the device and a  
               face-up bin at the back of the device -- firmware will not  
               provide a means of selecting between the two, nor will it  
               report which of the two gets used.  For this reason, bit 0  
               (cOutbin1) of this collection is being used to designate  
               both of these bins together."  
::={ job-info 20 }  
                
                
job-info-physical-outbins-used OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates which physical output bins this job has delivered		  
               printed pages to. The last OID field for this dynamic object		  
               contains the job ID.  
               Additional information:  
               The output bins designated by the bits of  
               this collection include the standard output bin(s) plus the  
               physical bins of attached external paper handling devices.  
               The configuration (if any) of external paper handling devices  
               will determine the mapping of individual bits in this  
               collection to the physical bins of the devices.  
               For LaserJet 4100 and LaserJet 4550, the cOutbin1 is used for Face Down  
               bin, cOutbin2 is used for Face Up bin, and 3-15 are used for  
               the 13 optional output bins (12 plus an extension to the Face  
               Up bin) for backwards compatibility with LaserJet 8000/LaserJet 8100 and  
               forwards compatibility with LaserJet 8150.  However, since they  
               cannot distinguish output going to the Face Up or Face Down  
               bin in the firmware because the diverter can only be moved  
               manually, bit 0 (cOutbin1) is being used to designate  
               both of these bits together.  If an external paper handling  
               output device is connected, then bit 2 (cOutbin3) will  
               represent the device's first output bin (and so on)."  
::={ job-info 22 }  
                
                
job-info-attr-1 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. Attribute objects are saved sequentially, starting		  
               with 1, after the start of a job. If more attributes are set		  
               than there are objects to store them, the excess JOBATTR values		  
               are ignored. If the corresponding SET JOBATTR= command has not		  
               been received when a get is done for this object, a status of		  
               <noSuchName> will be returned."  
::={ job-info-attribute 1 }  
                
                
job-info-attr-2 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 2 }  
                
                
job-info-attr-3 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 3 }  
                
                
job-info-attr-4 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 4 }  
                
                
job-info-attr-5 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 5 }  
                
                
job-info-attr-6 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 6 }  
                
                
job-info-attr-7 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 7 }  
                
                
job-info-attr-8 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 8 }  
                
                
job-info-attr-9 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 9 }  
                
                
job-info-attr-10 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 10 }  
                
                
job-info-attr-11 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 11 }  
                
                
job-info-attr-12 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 12 }  
                
                
job-info-attr-13 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 13 }  
                
                
job-info-attr-14 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 14 }  
                
                
job-info-attr-15 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 15 }  
                
                
job-info-attr-16 OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns the value that was set in PJL via the SET JOBATTR=		  
               command. See JOB-INFO-ATTR-1 for details."  
::={ job-info-attribute 16 }  
                
                
job-info-requested-originals OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The number of requested collated copies. The value was supplied		  
               with the job via PJL QTY variable, the PostScript Collate and		  
               NumCopies entries in the page device dictionary, or via some		  
               other mechansim."  
::={ job-info 24 }  
                
                
job-info-page-count-current-original OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The page number being printed within the current copy of a		  
               collated multi-copy job. This value changes when the		  
               job-info-pages-printed changes. The job-info-pages-printed		  
               indicates the total number of pages printed in the job, while		  
               this object indicates the number of pages printed for this copy		  
               of a collated multi-copy job.  
               Additional information:  
               The number of pages in the current copy of a collated  
               multi-copy job which have been completely printed and  
               safely delivered to the output bin."  
::={ job-info 25 }  
                
                
job-info-pages-in-original OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of pages in a single copy of a collated multi-copy job."  
::={ job-info 26 }  
                
                
job-info-printed-originals OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of collated copies completely printed and delivered to		  
               the output bin at time of query."  
::={ job-info 27 }  
                
                
job-info-accounting-media-size OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eLedger(11),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eROC8K(19),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eISOandJISA3(27),  
		  eJISB5(45),  
		  eJISB4(46),  
		  eISOB5(65),  
		  eJapansePostcardDouble(72),  
		  eMonarch(80),  
		  eCommercial10(81),  
		  eInternationalDL(90),  
		  eInternationalC5(91),  
		  eInternationalB5(100),  
		  eCustom(101),  
		  eUSLetterR(258),  
		  eISOandJISA4R(282),  
		  eUnknownMediaSize(32767)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the media size of the printed job. The media size of		  
               the first page will decide the media size of the entire job.		  
               The return value of this object will only be valid when the		  
               printer finishes printing the entire job."  
::={ job-info-accounting 1 }  
                
                
job-info-accounting-media-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUnknownMedia(1),  
		  eStandardType(2),  
		  ePreprinted(3),  
		  eBond(4),  
		  eLetterhead(5),  
		  eTransparency(7),  
		  eLabels(8),  
		  eRecycled(9),  
		  eColored(10),  
		  eCardStock(11),  
		  eRough(12),  
		  ePrepunched(13),  
		  eHeavy(14),  
		  eUserType1(16),  
		  eUserType2(17),  
		  eUserType3(18),  
		  eUserType4(19),  
		  eUserType5(20)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the media type of the printed job. The media type of		  
               the first page will decide the media type of the entire job.		  
               The return value of this object will only be valid when the		  
               printer finishes printing the entire job."  
::={ job-info-accounting 2 }  
                
                
job-info-accounting-finishing-options OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNoFinish(1),  
		  eOffset(2),  
		  ePunch(3),  
		  eStapler(4),  
		  eFinisher(5)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the finishing option used on the printed job. The		  
               finishing option specified for the first page will decide the		  
               finishing option of the entire job. The return value of this		  
               object will only be valid when the printer finishes printing		  
               the entire job."  
::={ job-info-accounting 3 }  
                
                
job-info-accounting-media-simplex-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of simplex pages printed in a		  
               particular job."  
::={ job-info-accounting 4 }  
                
                
job-info-accounting-media-duplex-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of duplex pages printed in a		  
               particular job."  
::={ job-info-accounting 5 }  
                
                
job-info-accounting-grayscale-impression-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of monochrome pages printed in a		  
               particular job."  
::={ job-info-accounting 6 }  
                
                
job-info-accounting-color-impression-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of color pages printed in a		  
               particular job."  
::={ job-info-accounting 7 }  
                
                
job-info-accounting-black-dots OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of black pixels used in a particular		  
               job."  
::={ job-info-accounting 8 }  
                
                
job-info-accounting-yellow-dots OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of yellow pixels used in a particular		  
               job."  
::={ job-info-accounting 9 }  
                
                
job-info-accounting-cyan-dots OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of cyan pixels used in a particular		  
               job."  
::={ job-info-accounting 10 }  
                
                
job-info-accounting-magenta-dots OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of magenta pixels used in a		  
               particular job."  
::={ job-info-accounting 11 }  
                
                
job-info-accounting-scanned-media-simplex-count OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of simplex pages scanned, indexed by		  
               media size. For each media size that is scanned, there are 6		  
               bytes of information in the following format.    	  
                   media-size number of scanned pages    	  
                   01 2345    	  
                   Bytes 0-1 contain a value from the media-size enum and		  
                       bytes 2-5 contain the number of the media size scanned.		  
                          	  
               For example if a 10 Letter pages are scanned followed by 5		  
               Legal pages scanned, the pValue of the object would be		  
               '02000A030005'  
               Additional information:  
               Contains the total number of simplex pages scanned, indexed by  
               media size. For each media size that is scanned, there are 6  
               bytes of information in the following format.     
               media-size number of scanned pages     
               01 2345     
               Bytes 0-1 contain a value from the media-size enum and  
               bytes 2-5 contain the number of the media size scanned.  
                 
               For example if a 10 Letter pages are scanned followed by 5  
               Legal pages scanned, the pValue of the object would be  
               '02000A030005'"  
::={ job-info-accounting 12 }  
                
                
job-info-accounting-scanned-media-duplex-count OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..80))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Contains the total number of duplex pages scanned, indexed by		  
               media size. For each media size that is scanned, there are 6		  
               bytes of information in the following format.    	  
                   media-size number of scanned pages    	  
                   01 2345 Bytes 0-1 contain a value from the media-size enum		  
                       and bytes 2-5 contain the number of the media size		  
                       scanned.    	  
               For example if a 10 Letter pages are scanned followed by 5		  
               Legal pages scanned, the pValue of the object would be		  
               '02000A030005'  
               Additional information:  
               Contains the total number of duplex pages scanned, indexed by  
               media size. For each media size that is scanned, there are 6  
               bytes of information in the following format.     
               media-size number of scanned pages     
               01 2345 Bytes 0-1 contain a value from the media-size enum  
               and bytes 2-5 contain the number of the media size  
               scanned.     
               For example if a 10 Letter pages are scanned followed by 5  
               Legal pages scanned, the pValue of the object would be  
               '02000A030005'"  
::={ job-info-accounting 13 }  
                
                
job-info-accounting-job-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  ePrintJob(1),  
		  eIPPJob(2),  
		  eCopyJob(3),  
		  eCopyInterruptJob(4),  
		  eJetSendJob(5),  
		  eInternalPage(6),  
		  eCleaningPage(7),  
		  eAutoCleaningPage(8),  
		  eDigitalSendJob(9),  
		  eWebPrintJob(10),  
		  eFaxPrintJob(11),  
		  eRetrievedJob(12),  
		  ePhotoCardPrintJob(13),  
		  eUnknownJob(1000)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Keeps track of what type of job is processed. "  
::={ job-info-accounting 14 }  
                
                
held-job-user-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..40))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "User name that is obtained by the driver through some internal		  
               method or from user input.  
               Additional information:  
               The following is a general description for all the JOB-MANAGEMENT  
               objects described below.  These object describe the attributes of the  
               dynamic list containing all the stored jobs on the disk available for  
               printing or deleting via the job-management feature.  The jobs on this  
               list are not deleted from the disk unless explicitly specified by the  
               user.  A print job may be specified for retention by PJL commands in the  
               data stream.  
                 
               Following is a list of the PJL commands (i.e. these comments describe   
               the PJL implementation and in some cases do not reflect the PML   
               implementation.):  
                 
               @PJL SET HOLD=OFF|ON|PROOF|STORE|PRINT  
                 
               GENERAL DESCRIPTION:   
                 
               This variable specifies the retention classification of the job.  The  
               values indicate whether the job is printed immediately and/or stored.  
                 
               OFF:  The job is printed but not retained on disk after printing.  This  
               is the default value.  
                 
               ON:  This setting may be thought of as free proof-and-hold.  The  
               requested number of copies will be printed and the job will be  
               temporarily stored on disk.  The job will then be available for printing  
               additional copies through the control panel and through PML.  There will  
               be a limit to the number of these temporary jobs that may be stored, and  
               when the limit is exceeded the oldest job will be removed from the disk.  
                 
               PROOF:  One copy of the job is printed and remaining copies are stored  
               on disk.  The job is then available to select for printing via the  
               control panel menus or PML.  The job will be deleted from the disk when  
               the disk space is needed for another proof and hold job but only after  
               the additional copies have been printed.  It will also be deleted when  
               the user sends down another proof and hold job with the same job name,  
               or the user explicitly deletes the job.  
                 
               STORE:  The job is not printed immediately but is retained on disk.  The  
               job is available to select for printing via the control panel  
                 
               DEFAULT VALUE: OFF  
                 
               The value will be stored in RAM only, not in NVRAM.  
               The legal PJL commands are SET and INQUIRE.  DEFAULT is not allowed.  
               The variable will appear in the PJL INFO VARIABLES list.  
                 
               @PJL SET USERNAME=<80 bytes>  
                 
               GENERAL DESCRIPTION:   
                 
               Eighty-character user name that is obtained by the driver through some  
               internal method or from user input.  If the job stream does not contain  
               a USERNAME the default value will be NO USER NAME.  The driver is  
               responsible for determining the size of the printers control panel and  
               sending a string of appropriate length.  
                 
               DEFAULT VALUE: NO USER NAME  
                 
               The value will be stored in RAM only, not in NVRAM.  
               The legal PJL commands are SET and, INQUIRE. DEFAULT is not allowed.  
               The variable will appear in the PJL INFO VARIABLES list.  
                 
               @PJL SET JOBNAME=<80 bytes>  
                 
               GENERAL DESCRIPTION:  
                 
               Eighty-character job name that may be generated by the driver or  
               obtained from user input.  This value may be used in conjunction with  
               the USERNAME to select a job from the front panel.  If the job stream  
               does not contain a JOBNAME, the printer will assume no job name; each  
               subsequent job that is sent down by the same user would replace the  
               users last job on disk.  The driver is responsible for determining the  
               size of the printers control panel and sending a string of appropriate  
               length.  
                 
               NOTE:  The limit of 80 bytes is a PJL limit.  The limit for PML will  
               be 40 bytes.  
                 
               DEFAULT VALUE: NULL STRING  
                 
               The value will be stored in RAM only, not in NVRAM.  
               The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed.  
               The variable will appear in the PJL INFO VARIABLES list.  
                 
               @PJL SET HOLDTYPE=PUBLIC|PRIVATE  
                 
               GENERAL DESCRIPTION:  
                 
               This variable specifies the privacy level of the job.  
                 
               PUBLIC:  The job does not require a PIN in order to be released for  
               printing.  This is the default value.  
                 
               PRIVATE:  The job requires a PIN in order to be released for printing.  
               The PIN is specified by the HOLDKEY variable.  If the  
                 
               HOLDTYPE is set to PRIVATE, a HOLDKEY value must be specified.  If no  
               HOLDKEY is specified, the job will be considered PUBLIC.  
                 
               DEFAULT VALUE: PUBLIC  
                 
               The value will be stored in RAM only, not in NVRAM.  
               The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed.  
               The variable will appear in the PJL INFO VARIABLES list.  
                 
               @PJL SET HOLDKEY=4 digits, 0000...9999  
                 
               GENERAL DESCRIPTION:  
                 
               A 4-digit string, each digit 0-9, that is specified in the job stream  
               and then required to be entered in order to release the job for  
               printing.  If a HOLDTYPE is PRIVATE, a HOLDKEY value must be specified.  
               If no HOLDKEY value is specified, a job will be considered PUBLIC.  
                 
               DEFAULT VALUE: NULL STRING  
                 
               The value will be stored in RAM only, not in NVRAM.  
               The legal PJL commands are SET and INQUIRE. DEFAULT is not allowed.  
               The variable will appear in the PJL INFO VARIABLES list.  
                 
                 
               The format for the OID is as follows:  
                 
               3.4.1.6.x.y  
               <-----> | |  
               |    |  \  
               /     |  job-id in the system  
               /       \     
               PML_JOB_MGNT_ROOT_OID  \  
               job attribute 1..6  
                 
               x values are 1..6:  
                 
               1) user-name:  user name that is obtained by the driver through some  
               internal method or from user input.  
                 
               2) job-name:  job name may be generated by the driver or obtained from  
               user input.  
                 
               3) hold:  indicates the retention classification of the job.  The values  
               indicate whether the job is printed immediately and/or stored.  There  
               are 4 options:  
               OFF:    The job is printed but not retained on the disk.  
               ON:     The job is printed and stored temporarily on the disk.  
               STORE:  The job is not printed but stored on the disk.  
               PROOF:  One copy of the job is printed and the remaining copies are  
               stored on the disk.  
                 
               4) holdtype:  The variable specifies the security level of the job.  
               PUBLIC:  The job does not require a PIN in order to release the job for  
               printing.  
               PRIVATE:  The job requires a PIN in order to be released for printing.  
                 
               5) quantity:  number of copies to print.  Valid values are 0..999.  
                 
               6) pin:  A 4 digit string, each digit is 0-9, that is specified in the  
               job stream and then required to be entered in order to release the job  
               for printing.  
                 
               y :  an unsigned 32-bit number which uniquely identifies the job.  The job  
               id for the job remains the same for the job until it is deleted from the  
               held jobs list.  
                 
                 
               For example, the OID below is asking for the user name of the  
               job whose id is 3.  The application would issue:  
                 
               OID      
               get 3.4.1.6.1.3  
                 
               For example, the <getnext> OID values sequence is as follows:  
                 
               OID                returned OID  
               getnext 3.4.1.6         3.4.1.6.1.1  
               getnext 3.4.1.6.1.1     3.4.1.6.1.2  
               getnext 3.4.1.6.2.1     3.4.1.6.2.2  
               ***  
               getnext 3.4.1.6.1.6     3.4.1.6.1.7  
               getnext 3.4.1.6.2.1     3.4.1.6.2.2  
               getnext 3.4.1.6.5.2828  3.4.1.6.6.1   
                 
               NOTE: for example above, job id 2828 is the last job in the list of  
               held jobs.  
               ***  
                 
               Also supported is <getnext> on the job attributes:  
               OID                returned OID  
               getnext 3.4.1.6.1       3.4.1.6.1.1  
               getnext 3.4.1.6.6       3.4.1.6.6.1"  
::={ held-job-info 1 }  
                
                
held-job-job-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..40))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The job name may be generated by the driver or obtained from		  
               user input."  
::={ held-job-info 2 }  
                
                
held-job-retention OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eHoldOff(1),  
		  eHoldOn(2),  
		  eHoldStore(3),  
		  eHoldProof(4)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates the retention classification of the job. The values		  
               indicate whether the job is printed immediately or stored.		  
               There are 4 options:    	  
                   eHoldOff: The job is printed but not retained on the disk.		  
                          	  
                   eHoldOn: The job is printed and stored temporarily on the		  
                       disk.    	  
                   eHoldStore: The job is not printed but stored on the disk.		  
                          	  
                   eHoldProof: One copy of the job is printed and the		  
                       remaining copies are stored on the disk.   "  
::={ held-job-info 3 }  
                
                
held-job-security OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eHoldTypePublic(1),  
		  eHoldTypePrivate(2)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The variable specifies the security level of the job.    	  
                   eHoldTypePublic: The job does not require a PIN in order to		  
                       release the job for printing.    	  
                   eHoldTypePrivate: The job requires a PIN in order to be		  
                       released for printing.   "  
::={ held-job-info 4 }  
                
                
held-job-quantity OBJECT-TYPE  
  SYNTAX      INTEGER(1..999)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of copies to print."  
::={ held-job-info 5 }  
                
                
held-job-pin OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..4))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "A string that is specified in the job stream and then required		  
               to be entered in order to release the job for printing. PIN		  
               stands for Personal Identification Number.  
               Additional information:  
               Must be a 4 digit string, each digit must be 0..9 or a null string  
               if there is no pin.  
               		For security purposes, you can no longer get the value of the PIN."  
::={ held-job-info 6 }  
                
                
held-job-print OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(12))  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Instructs the printer to schedule the specified held job for		  
               printing with the specified number of copies. The job-id is		  
               used to identify which job to print. A held job can also be		  
               printed from the control panel.  
               Additional information:  
               Bytes 0-3 is the job id of the job to print.  
               Bytes 4-7 is the number of copies to print.  
               Bytes 8-11 (optional) contain the PIN for  
               a Private job. "  
::={ held-job-control 1 }  
                
                
held-job-delete OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Instructs the printer to delete the specified held job from the		  
               list. The job-id is used to identify which job to delete. A		  
               held job can also be deleted from the control panel.  
               Additional information:  
               Setting this to a value that is not a Held Job on the  
               system or is a Private Held Job returns <ErrUnsupValue>.  
               To delete a private Held Job, you must use the PML object  
               HELD-JOB-PRINT with a quantity of 0 and supply the correct  
               HELD-JOB-PIN with the request. (See HELD-JOB-PRINT)"  
::={ held-job-control 2 }  
                
                
held-job-set-queue-size OBJECT-TYPE  
  SYNTAX      INTEGER(0..100)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the maximum number of jobs which can be stored in the held		  
               job list.  
               Additional information:  
               Sets the size of the temporary job lists queue."  
::={ held-job-control 3 }  
                
                
held-job-enable OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eDisabled(1),  
		  eEnabled(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Enables or disables Job Retention (Job Hold). The valid values		  
               are eDisabled and eEnabled. (Specifying an invalid mode causes		  
               an <badValue> error to be returned.) When		  
               eDisabled is specified all Job Retention (Hold, Proof, Store,		  
               PIN Printing) is disabled. When eEnabled is specified, the Job		  
               Retention characteristics of a given job are defined by the PJL		  
               variable SET HOLD.  
               Additional information:  
               When disabled, held jobs are not removed,  
               but must be explicitly removed through the Control Panel  
               or the PML object HELD-JOB-DELETE."  
::={ held-job-control 4 }  
                
                
mopy-mode OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eStandard(4),  
		  eEnhanced(5)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Controls or reports how mopies are generated. eOff turns off		  
               the mopy feature. eAuto allows the device to determine the best		  
               method for generating mopies based on the device configuration.		  
               eStandard spools the I/O data and replays the I/O data multiple		  
               times to generate the mopies. eEnhanced spools the rasterized		  
               page images and replays the rasterized data to generate the		  
               mopies. Typically, the rasterized data will be larger and will		  
               allow all but the first mopy to print at speed. If the job		  
               being mopied is not extremely complex, then the first mopy will		  
               print at speed also."  
::={ settings-spooler 1 }  
                
                
                
date-display OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eDateDisplayMMM-DD-YYYY(4),  
		  eDateDisplayDD-MMM-YYYY(5),  
		  eDateDisplayYYYY-MMM-DD(6)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Controls front-panel date display format.  
               Additional information:  
               Controls front-panel date display format."  
::={ settings-system 22 }  
                
                
date-and-time OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "A C structure containing the following fields:    typedef		  
               struct {    	  
                   ubyte yr; /* year: 0 to 99 */    	  
                   ubyte mon; /* month: 1 to 12 */    	  
                   ubyte day; /* day: 1 to 31 */    	  
                   ubyte wday; /* Day of week: 1 to 07 */    	  
                   ubyte hr; /* hour: 0 to 23 */    	  
                   ubyte min; /* minute: 0 to 59 */    	  
                   ubyte sec; /* second: 0 to 59 */    	  
                   } date_t;    	  
               where ubyte is an unsigned byte (0-255).  
               Additional information:  
               A C structure containing the following fields:    typedef  
               struct {     
               ubyte yr;   /* year: 3 to 99 */     
               ubyte mon;  /* month: 1 to 12 */     
               ubyte day;  /* day: 1 to 31 */     
               ubyte wday; /* Day of week: 1 to 07 */     
               ubyte hr;   /* hour: 0 to 23 */     
               ubyte min;  /* minute: 0 to 59 */     
               ubyte sec;  /* second: 0 to 59 */     
               } date_t;     
               where ubyte is an unsigned byte (0-255)."  
::={ status-system 17 }  
                
                
time-display OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eTimeDisplayTwelveHour(1),  
		  eTimeDisplayTwentyFourHour(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Controls front-panel time display format. Set to		  
               eTimeDisplayTwelveHour for AM/PM display. Set to		  
               eTimeDisplayTwentyFourHour for military-type display.  
               Additional information:  
               Controls front-panel time display format. Set to  
               eTimeDisplayTwelveHour for AM/PM display. Set to  
               eTimeDisplayTwentyFourHour for military-type display."  
::={ status-system 28 }  
                
                
direct-connect-ports-enable OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eFalse(1),  
		  eTrue(2),  
		  eUnSupported(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object specifies whether all direct connect ports		  
               (parallel and USB) are available or ignored. JetDirect,		  
               embedded network connectivity, and third party add-on cards		  
               (such as Firewire) will be unaffected by setting this object."  
::={ settings-system 43 }  
                
                
mio1-model-name OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns product information identifying the I/O card. Example:		  
               XXXX."  
::={ mio1 2 }  
                
                
mio1-manufacturing-info OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns information describing the manufacture of the I/O card		  
               installed in MIO/EIO slot 1. May include serial number and		  
               firmware revision.  
               Additional information:  
               The format of the string returned is determined by  
               the manufacturer of the EIO device. There is no standard for   
               content of the string."  
::={ mio1 3 }  
                
                
mio1-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eDiskDrive(8),  
		  eIOCard(12)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in		  
               MIO/EIO slot 1. See SIMM1-TYPE for an explanation of the		  
               enumerations."  
::={ mio1 4 }  
                
                
mio2-model-name OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns product information identifying the I/O card. Example:		  
               XXXX."  
::={ mio2 2 }  
                
                
mio2-manufacturing-info OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns information describing the manufacture of the I/O card		  
               installed in MIO/EIO slot 2. May include serial number and		  
               firmware revision.  
               Additional information:  
               The format of the string returned is determined by  
               the manufacturer of the EIO device. There is no standard for   
               content of the string."  
::={ mio2 3 }  
                
                
mio2-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eDiskDrive(8),  
		  eIOCard(12)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in		  
               MIO/EIO slot 2. See SIMM1-TYPE for an explanation of the		  
               enumerations."  
::={ mio2 4 }  
                
                
mio3-model-name OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns product information identifying the I/O card. Example:		  
               XXXX."  
::={ mio3 2 }  
                
                
mio3-manufacturing-info OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns information describing the manufacture of the I/O card		  
               installed in MIO/EIO interface 3. May include serial number and		  
               firmware revision.  
               Additional information:  
               The format of the string returned is determined by  
               the manufacturer of the EIO device. There is no standard for   
               content of the string."  
::={ mio3 3 }  
                
                
mio3-type OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eEmpty(1),  
		  eUnknown(2),  
		  eDiskDrive(8),  
		  eIOCard(12)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns an indication of the type of option installed in		  
               MIO/EIO interface 3. See SIMM1-TYPE for an explanation of the		  
               enumerations."  
::={ mio3 4 }  
                
                
io-timeout OBJECT-TYPE  
  SYNTAX      INTEGER(5..300)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The amount of time, in seconds, to wait for more print job data		  
               to be received before an I/O timeout occurs. The I/O channel		  
               being timed is the I/O channel that received the data		  
               associated with the current print job. If an I/O timeout		  
               occurs, the PDL processing sub-system assumes all the data		  
               associated with the current print job has been received, and		  
               processes the end of job in a PDL specific manner. The POS		  
               specifies the supported values.  
               Additional information:  
               If an I/O timeout occurs,the PDL processing  
               sub-system will consider it an end of job condition only  
               if there is data from another I/O subsystem waiting to be  
               processed.      
               The supported values are 5 to 300 seconds.   
               Setting to a value outside the supported range returns   
               <noError> status and the  
               value will be snapped to the nearest supported value."  
::={ settings-io 1 }  
                
                
io-switch OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eYes(1)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates if the device will switch between I/O channels when a		  
               job boundary is encountered and print job data is available on		  
               another I/O channel."  
::={ settings-io 2 }  
                
                
port1-parallel-speed OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eSlow(1),  
		  eFast(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the maximum parallel I/O port speed, for		  
               port 1. This object is only supported if this port is a		  
               parallel port. An eSlow setting causes a 10 us busy pulse per		  
               received byte of data. An eFast setting causes a 1.5 us busy		  
               pulse per received byte of data. In rare cases, setting this		  
               value to eFast can cause the parallel port to no longer		  
               transfer data reliably.  
               Additional information:  
               When the value of this object is changed, it takes   
               effect immediately. It is recommended that the printer  
               be offline and not in a job when this object is changed."  
::={ port1 4 }  
                
                
port1-parallel-bidirectionality OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUnidirectional(1),  
		  eBidirectional(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes whether the parallel I/O port supports		  
               bidirectional communication for port 1. This object is only		  
               supported if this port is a parallel port.  
               Additional information:  
               A get on this object returns the current mode   
               for the parallel port. Setting this object specifies whether   
               or not bidirectional communications will be allowed."  
::={ port1 5 }  
              
              
              
rpc-bind-protocol-address OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Array of Berkeley sockets style protocol addresses used to bind		  
               RPC to a communications protocol family. Setting an instance of		  
               this array object to a zero length binary value disables the		  
               transport protocol indicated by that instance. All multi-bytes		  
               fields are in network (or big-endian) order. Bytes 1 and 2		  
               indicate the transport protocol. Some of the transport protocol		  
               mapping information can be found in RFC 1010 Assigned Numbers.		  
               A list of interesting transport protocol number mappings		  
               include:    	  
                   <table>  
                   Protocol | Number  
                   ---------+-------  
                    UDP/IP  |  17   
                     IPX    |  1000   
                     MLC    |  4660  
                   </table>  
                   Bytes 3 and 4 indicate the address family. The address		  
                       family uses the same mapping as the BSD sockets address		  
                       family. A list of interesting address family mappings		  
                       include:    	  
                   <table>  
                   Address Family | Number  
                   ---------------+-------  
                       Internet   |   2  
                       NetWare    |   6  
                       MLC        | 22136   
                   </table>  
               The format the fifth and following bytes is dependent on the		  
               address family. For the Internet address family, bytes 5 and 6		  
               contain the port number, bytes 7 through 10 contain the IP		  
               address, and the following eight bytes are unused. For NetWare,		  
               bytes 5 through 8 are the network number, bytes 9 through 14		  
               are the node number, and bytes 15 and 16 are the socket		  
               number.  
               Additional information:  
               The length of the binary value is zero  
               if the instance of an object in the rpc-bind-protocol-address  
               array is not in use.  
               Returns <noSuchName>  
               status if attempting to access this object and there  
               is no storage device is installed."  
::={ settings-rpc 2 }  
                
                
rpc-bound-protocol-address OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "An array of Berkeley sockets style protocol addresses that the		  
               NFS service has been bound to successful. The format is that		  
               same as the array of RPC-BIND-PROTOCOL-ADDRESS of objects.  
               Additional information:  
               Returns <noSuchName>  
               status if attempting to access this object and there  
               is no storage device is installed."  
::={ status-rpc 3 }  
                
                
                
file-system-max-open-files OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The number of open files allowed at one time. Opening a file		  
               when the maximum number of files are currently open will fail.  
               Additional information:  
               Indicates the number of open files a  
               personality (e.g. PCL or PostScript) is guaranteed to be  
               able to open before the file system runs out of file handles.  
               		   This object is between 1 and 500.  
               Returns <noSuchName>  
               status if attempting to access this object and there  
               is no storage device is installed."  
::={ settings-file-system 2 }  
                
                
file-system-set-system-partition-writeable OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "This object allows the system partition to be written to. It		  
               consists of a C structure containing the following fields:    	  
                   typedef struct {    	  
                   ubyte <<hidden>>[8];    	  
                   ubyte volumenumber;    	  
                   } fs_writeable_system_partition_t;    	  
                   which is described below:    	  
                   Bytes 0 - 7: contain the <<hidden>>    	  
                   Byte 8 : is the volume number    	  
               Access to this command is controlled by the <<hidden>>. If the		  
               <<hidden>> supplied is incorrect the command will fail. The		  
               volumenumber is a volume number of an existing system		  
               partition.  
               Additional information:  
               Returns <noSuchName>  
               status if attempting to access this object and there  
               is no storage device is installed.  
               Returns <badValue> if the <<hidden>> is incorrect or if  
               		   the volume requested is not present."  
::={ settings-file-system 6 }  
                
                
file-system-set-system-partition-readonly OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Changes a system partition to be READ-ONLY. The value is the		  
               volume number to change. If the volume number specified is NOT		  
               a system partition an error is returned.  
               Additional information:  
               Returns <noSuchName>  
               status if attempting to access this object and there  
               is no storage device is installed.  
               Returns <badValue> if the volume requested  
               		   is not present."  
::={ settings-file-system 7 }  
                
                
file-system-delete-files OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Setting this object causes the specified filename to be		  
               deleted, after first validating that the authentication data is		  
               correct for the specified user ID.    	  
                   The format for this object is a C structure:   	  
                   typedef struct {    	  
                   sint32 UserId;    	  
                   uint16 AuthenticationDataLen    	  
                   ubyte AuthenticationData[]    	  
                   char Filename[];    	  
                   } fs_delete_files_t;    	  
                   which is described below:   	  
                   Bytes 0 - 3: contains a user id represented as a multi-byte		  
                       value that is stored in big-endian format, where the		  
                       most significant byte occurs first.    	  
                   Bytes 4 - 5 : Length of the Athentication data that follows		  
                       starting at offset 6. Stored as a multi-byte value that		  
                       is stored in big-endian format, where the most		  
                       significant byte occurs first.    	  
                   Bytes 6 - 6+AuthenticationDataLen : a ubyte array		  
                       containing the Authentication data used to verify		  
                       access for this operation.   	  
                   Bytes starting at offset (6+AuthenticationDataLen+1): A		  
                       null terminated character array representing the ASCII		  
                       file name to be deleted. The length of the string will		  
                       be limited by the remaining space in the object.    	  
               This string represents a fully-qualified path name which may		  
               specify a filename or a regular expression that may match		  
               multiple files (e.g <path>/*.exe). Access to this command is		  
               controlled by the UserId and the authentication data. If the		  
               UserID or authentication data supplied is incorrect the command		  
               will fail. The device POS will specify any limitations to the		  
               length of the filename string, what constitutes a correct user		  
               ID, what constitutes correct authentication data, and the		  
               significance of any return values.  
               Additional information:  
               Setting this object causes the specified filename  
               to be deleted, after first validating that the  
               authentication data is correct for the specified  
               user ID.  This object is always present.  
                 
               The format for this object is a C structure:  
                 
               typedef struct {          
               sint32 UserId;          
               uint16 AuthenticationDataLen   
               ubyte  AuthenticationData[]    
               char   Filename[];       
               } fs_delete_files_t;     
                 
               Bytes 0 - 3: contains a user id represented  
               as a multi-byte value that is stored in big-endian  
               format, where the most significant byte occurs first.  
                 
               Bytes 4 - 5 : Length of the authentication data that  
               follows starting at offset 6. Stored as a multi-byte  
               value that is stored in big-endian format, where the  
               most significant byte occurs first.   
                 
               Bytes 6 - 6+AuthenticationDataLen : a ubyte array  
               containing the authentication data used to verify  
               access for this operation.  
                 
               Bytes starting at offset (6+AuthenticationDataLen+1):  
               A null terminated character array representing the  
               ASCII file name to be deleted. The length of the  
               string will be limited by the remaining space in the  
               object.  This string represents a fully-qualified path   
               name which may specify a filename or a file-type regular   
               expression that may match multiple files (e.g.,  
               <path>/*.exe).   
                 
               Access to this command is controlled by the UserId  
               and the authentication data.  If the UserID or   
               authentication data supplied is incorrect the   
               command will fail.  
                 
               The device POS will specify any limitations to the  
               length of the filename string, what constitutes a  
               correct user ID, what constitutes correct  
               authentication data, and the significance of any  
               return values."  
::={ settings-file-system 8 }  
                
                
file-system-external-access-capabilities OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object is used to control access to the file system of the		  
               device. It is always readable. It is writable when		  
               <<hidden>> is not the empty string,		  
               and a successful write to that object with the current <<hidden>>		  
               has preceded the write to this object. In other words, the		  
               <<hidden>> must be in the		  
               'authenticated state' for a write on		  
               FILE-SYSTEM-EXTERNAL-ACCESS-CAPABILITIES to succeed. After the		  
               object has successfully been written to, it becomes read-only,		  
               and the <<hidden>> object exits the		  
               authenticated state. <<hidden>>must		  
               then be written to again with the current <<hidden>> in order to		  
               make another write operation on		  
               FILE-SYSTEM-EXTERNAL-ACCESS-CAPABILITIES possible.    	  
                   cDisablePJLFileSystemAccess - All file system access		  
                       through PJL will be disabled.    	  
                   cDisablePMLFileSystemWrite - All file-systems-related PML		  
                       objects such as FILE-SYSTEM-DELETE-FILES or		  
                       hrPartitionLabel become read-only. For objects that are		  
                       normally write-only this means that no successful		  
                       operations can now be performed on them.    	  
                   cDisableNFSFileSystemAccess - All NFS file system access		  
                       will be disabled.    	  
                   cDisablePSFileSystemAccess - All file system access through		  
                       PostScript will be disabled.    	  
                   cDisableEWSFileSystemAccess - All access to the file system		  
                       by the Embedded Web Server will be disabled.   "  
::={ settings-file-system 10 }  
                
                
file-system-erase-mode OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object is used to control how file data is handled when		  
               files are deleted. It is always readable. It is writable when		  
               <<hidden>> is the empty string or		  
               when a write to <<hidden>> with the		  
               current <<hidden>> has preceeded the write to the object. When		  
               <<hidden>> is not the empty string		  
               then this object becomes read-only after a successful write to		  
               it. <<hidden>> must then be written		  
               to again with the current <<hidden>> in order to make another		  
               write operation on the object possible. If the		  
               <<hidden>> is incorrectly set, this		  
               object becomes read-only until the <<hidden>> is correctly set.		  
               The logical settings for this object are:    	  
                   NonSecureFastErase - When a file is deleted, only the		  
                       reference to it in the file system tables is removed.		  
                       No file data is overwritten. This is the default		  
                       setting. This is the setting when both bits in the		  
                       collection are set to 0.   	  
                   SecureFastErase - File information is overwritten with		  
                       identical, random character pattern when it is deleted.		  
                       This is the setting when cEraseMode0 is set to 1 and		  
                       cEraseMode1 is set to 0.   	  
                   SecureSanitizeErase - Secure, repetitive algorithm used to		  
                       overwrite all deleted file information and remove any		  
                       residual data persistence. A random character is		  
                       written to all bytes of deleted sectors. Then the		  
                       complement of that character and finally, another		  
                       random character is written. This is the setting when		  
                       cEraseMode0 is set to 0 and cEraseMode1 is set to 1.   	  
               Note that an error will be returned for an attempt to set both		  
               bits of the collection to 1."  
::={ settings-file-system 11 }  
                
                
file-system-wipe-disk OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object is a non-leaf node which will have one leaf node		  
               under it for each file system in the printer. The leaf nodes		  
               will be in a 1-to-1 correspondence with the hrDeviceIndex		  
               objects. This object specifies for each leaf node whether the		  
               file system on the device is going to be erased according to		  
               the setting of the FILE-SYSTEM-ERASE-MODE referenced by the		  
               corresponding hrDeviceIndex. A file system will be overwritten		  
               on system reboot if this object is set to 1. It will be		  
               unchanged if this object is set to 0. If this object's value is		  
               -1 then the file system cannot be wiped. If the file system		  
               contains the permstore, the permstore will be saved off and		  
               restored after the file-system wipe is completed. This object		  
               is always readable. It is writable when		  
               <<hidden>> is the empty string or		  
               when a write to <<hidden>> with the		  
               current <<hidden>> has preceeded the write to the object. When		  
               <<hidden>> is not the empty string		  
               then this object becomes read-only after a successful write to		  
               it. <<hidden>> must then be written		  
               to again with the current <<hidden>> in order to make another		  
               write operation on the object possible. If the		  
               <<hidden>> is incorrectly set, this		  
               object becomes read-only until the <<hidden>> is correctly set."  
::={ settings-file-system 12 }  
                
                
file-system-wipe-disk-status OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is a non-leaf node which will have one leaf node		  
               under it for each file system in the printer. The leaf nodes		  
               will be in a 1-to-1 correspondence with the hrDeviceIndex		  
               objects. This object specifies for each leaf node the status of		  
               a disk wipe in progress. A return value of -1 indicates that no		  
               disk wipe is in progress. A return value in the range of 0 to		  
               100 indicates the percent done for a disk wipe in progress. All		  
               other values are illegal."  
::={ settings-file-system 13 }  
                
                
file-system2-initialize-volume OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eInitializing(2)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Setting this object to eInitializing causes file system 2 to be		  
               initialized. Reading this object indicates if the file system		  
               is currently being initialized.  
               Additional information:  
               The hrDeviceIndex value for the mass storage  
               device is the same value that is used to index into the  
               FILE-SYSTEM sub-tree.  Since this product supports  
               up to 3 physical mass storage device, and since the hrDeviceIndex  
               for the mass storage devices will start at 2 if the mass  
               	       storage device is installed, the FILE-SYSTEM2-INITIALIZE-VOLUME  
               	       object will be the object that allows the mass storage device to be   
               initialized that is the 1st device."  
::={ file-system2 6 }  
                
                
file-system3-initialize-volume OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eInitializing(2)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Setting this object to eInitializing causes file system 3 to be		  
               initialized. Reading this object indicates if the file system		  
               is currently being initialized.  
               Additional information:  
               The hrDeviceIndex value for the mass storage  
               device is the same value that is used to index into the  
               FILE-SYSTEM sub-tree.  Since this product supports  
               up to 3 physical mass storage device, and since the hrDeviceIndex  
               for the mass storage devices will start at 2 if the mass  
               	       storage device is installed, the FILE-SYSTEM3-INITIALIZE-VOLUME  
               	       object will be the object that allows the mass storage device to be   
               initialized that is the 2nd device."  
::={ file-system3 6 }  
                
                
file-system4-initialize-volume OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eInitializing(2)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Setting this object to eInitializing causes file system 4 to be		  
               initialized. Reading this object indicates if the file system		  
               is currently being initialized.  
               Additional information:  
               The hrDeviceIndex value for the mass storage  
               device is the same value that is used to index into the  
               FILE-SYSTEM sub-tree.  Since this product supports  
               up to 3 physical mass storage devices, and since the hrDeviceIndex  
               for the mass storage devices will start at 2 if the mass  
               	       storage device is installed, the FILE-SYSTEM4-INITIALIZE-VOLUME  
               	       object will be the object that allows the mass storage device to be   
               initialized that is the 3rd device."  
::={ file-system4 6 }  
                
                
mass-storage-resource-change-counter OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "A counter which changes when a mass storage based resource has		  
               been added or deleted.  
               Additional information:  
               The value of this counter changes   
               each time the MASS-STORAGE-RESOURCE-CHANGED object  
               is set to eTrue.  The value also changes when the   
               mass storage device is initialized.  However, the value does not  
               change when a mass storage device is removed and a different  
               mass storage device is installed.  Initializing all volumes sets   
               this object back to the factory default value.  A reboot sets  
               	   this object back to the factory devalut value.  
               Returns <noSuchName>  
               status if attempting to access this object and there  
               is no storage device is installed."  
::={ mass-storage-resources 1 }  
                
                
mass-storage-resource-changed OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eTrue(2)  
		  }  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "Setting to eTrue causes MASS-STORAGE-RESOURCE-CHANGE-COUNTER to		  
               be incremented.  
               Additional information:  
               Returns <noSuchName>  
               status if attempting to access this object and there  
               is no storage device is installed."  
::={ mass-storage-resources 2 }  
                
                
ram-disk-mode OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eAuto(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or controls RAM disk support. eOFF turns off the RAM		  
               disk functionality. eOn turns on the RAM disk functionality and		  
               creates a RAM disk whose size is controlled by the		  
               RAM-DISK-SIZE object. eAuto turns on the RAM disk functionality		  
               and creates a RAM disk size determined by the printer based on		  
               installed options and other memory related settings.  
               Additional information:  
               Returns or controls RAM disk support.  eOFF turns off  
               the RAM disk functionality. eAuto turns on  
               the RAM disk functionality and creates a RAM disk size  
               determined by the printer based on the amount of installed  
               memory."  
::={ settings-mass-storage-bd 1 }  
                
                
ram-disk-size OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns or controls the size of the RAM disk. The device POS		  
               specifies the minimum memory requirements. The object		  
               MAXIMUM-RAM-DISK-MEMORY specifies the maximum memory available		  
               for the RAM disk.  
               Additional information:  
               Returns the size of the RAM disk."  
::={ settings-mass-storage-bd 2 }  
                
                
maximum-ram-disk-memory OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object's name is misleading. This object does not return		  
               the maximum configurable RAM disk size. Instead, it returns the		  
               maximum amount of memory, in bytes, that can used to increase		  
               the size of the RAM disk.  
               Additional information:  
               This object returns the maximum amount of additional   
               memory that is available for increasing the size of the RAM   
               disk."  
::={ status-mass-storage-bd 1 }  
                
                
mono-color-switching-mode OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eAutoSwitch(1),  
		  eMostlyColor(2),  
		  eMostlyMono(3)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object allows the user to view/change the color/mono		  
               switching mode for a device.  
               Additional information:  
               This object allows the user to view/change the  
               color/mono switching mode for a device.  The behavior of   
               each setting may vary depending on the device. The value will  
               be stored in NVRAM"  
::={ settings-system 31 }  
                
                
device-configure-printer-parameters OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..256))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Allow the printer to be configured as a duplex or simplex		  
               printer. There will be a <<hidden>> encoded in this string and		  
               decoded by the printer firmware. If the <<hidden>> check passes		  
               the printer will be configured accordingly.  
               Additional information:  
               Used to configure engines for duplex enabled or not.  
               Encoded configuration string is passed in, which is decoded  
               by firmware.  Firmware verifies config. string is valid, and  
               retrieves device Configuration data.  
               Expandable to accommodate future products configuration needs."  
::={ device-configure 12 }  
                
                
job-input-auto-continue-timeout OBJECT-TYPE  
  SYNTAX      INTEGER(-1..3600)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The number of seconds the device waits after a job related		  
               continuable error occurs before automatically continuing. An		  
               example job related continuable error is the job requesting a		  
               media size that is not available. After the timeout expires,		  
               the device will continue processing the job as if a continue		  
               event occurred, such as the front panel continue key being		  
               pressed. If the value is -1, the device does not automatically		  
               continue after a job related continuable error occurs. If the		  
               value is 0, the device immediately continues. If the value is		  
               greater than 0, the value represents the timeout value in		  
               seconds.  
               Additional information:  
               The number of seconds the device waits after a job  
               related continuable error occurs before automatically  
               continuing.  An example job related continuable error is  
               the job requesting a media size that is not available.  
               After the timeout expires, the device will continue  
               processing the job accourding to the action defined by  
               JOB-INPUT-AUTO-CONTINUE-MODE.   
               If the value is -1, the device does not automatically continue  
               after a job related continuable error occurs.  If the  
               value is 0, the device immediately continues.  If the  
               value is greater than 0, the value represents the  
               timeout value in seconds.  
               The data for this object is stored in NVRAM."  
::={ status-system 35 }  
                
                
job-input-auto-continue-mode OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the device behavior when the desired media is		  
               not currently available.    	  
                   cCancelJob - The device cancels the job. The device POS		  
                       should explain what happens if this item is not the		  
                       only item in the collection.    	  
                   cAutoMediaSizeOverride - The device is allowed to		  
                       substitute a different size media.    	  
                   cAutoMediaNameOverride - The device is allowed to		  
                       substitute a different media name.    	  
                   cUSMediaSizeOverride - The device is allowed to substitute		  
                       US media sizes (letter, etc.) for ISO media sizes (A4,		  
                       etc.).    	  
                   cISOMediaSizeOverride - The device is allowed to substitute		  
                       ISO media sizes (A4, etc.) for US media sizes (letter,		  
                       etc.).     
               Additional information:  
               Returns or sets the device behavior when the desired  
               media is not currently available.  
               cCancelJob - The device cancels the job regardless of other  
               item settings.    
               cAutoMediaSizeOverride - The device is allowed to substitute   
               a different size media.  
               cAutoMediaNameOverride - The device is allowed to substitute   
               a different media name.  
               --                 cUSMediaSizeOverride - The device is allowed to substitute  
               --                              US media sizes (letter, etc.) for ISO media sizes  
               --                              (A4, etc.).  
               --                 cISOMediaSizeOverride - The device is allowed to substitute  
               --                              ISO media sizes (A4, etc.) for US media sizes  
               --                              (letter, etc.).  
               At least one bit of the collection must be set; setting  
               this object to zero will cause a status of  
               <badValue> to be returned.  
               This object describes the action that is performed when the  
               JOB-INPUT-AUTO-CONTINUE-TIMEOUT expires. "  
::={ status-system 36 }  
                
                
job-output-auto-continue-timeout OBJECT-TYPE  
  SYNTAX      INTEGER(-1..3600)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the time that the printer will wait after an		  
               output bin becomes full and the printer is trying to deliver a		  
               sheet of media to that output bin. When the timeout expires,		  
               the job is processed according to the OUTBINn-OVERRIDE-MODE. A		  
               value of -1 indicates that the printer will wait for a continue		  
               event. A non-negative value is the number of seconds to wait.  
               Additional information:  
               Returns or sets the time that the printer will wait  
               after an output bin becomes full and the printer is  
               trying to deliver a sheet of media to that output bin.  
               When the timeout expires, the job is processed according  
               to the OUTBINn-OVERRIDE-MODE.  A value of -1 indicates  
               that the printer will wait for a continue event.  A non-  
               negative value is the number of seconds to wait."  
::={ status-system 40 }  
                
                
model-number OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Identifies the device model number as listed in the HP		  
               corporate price list (e.g. C2121A for DeskJet 500C). The string		  
               is as specific as possible. Products should note in POS if the		  
               model number on the CPL changes but the device reports the		  
               previous model number. If the model number changes based on the		  
               installed options, the POS should indicate if only the base		  
               model number is returned, or if the device senses the installed		  
               options and returns the correct model number. If possible,		  
               encode the model number in a symbol set (like Roman-8) that		  
               matches the ASCII character set and limit the characters used		  
               to ASCII characters.  
               Additional information:  
               Identifies the device model number as listed in the HP  
               corporate price list (e.g.  C2121A for DeskJet 500C).  
               The string is as specific as possible.  
               The value of this object does not change based on   
               the installed options. The default of this object is the  
               same on all $product_str printers."  
::={ id 1 }  
                
                
model-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..32))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Identifies the device model name (e.g. ''DeskJet 1200C''). The		  
               string is as specific as possible. Capitalization and spacing		  
               should match family naming conventions. Products should note in		  
               POS if the model name on the HP corporate price list changes		  
               but the device reports the previous device name. If the model		  
               name changes based on the installed options, the POS should		  
               indicate if only the base model name is returned, or if the		  
               device senses the installed options and returns the correct		  
               model name. If possible, encode the model name in a symbol set		  
               (like Roman-8) that matches the ASCII character set and limit		  
               the characters used to ASCII characters.  
               Additional information:  
               Since the value of this object is frequently used in   
               displaying a list of printers, it is kept relatively short in  
               case systems have limited width for their display area. The  
               model name does not change based on sensing of installed options."  
::={ id 2 }  
                
                
formatter-serial-number OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object returns the formatter serial number for the device.		  
               The value returned from this object is the FORMATTERNUMBER		  
               system variable. If possible, encode the serial number in a		  
               symbol set (like Roman-8) that matches the ASCII character set		  
               and limit the characters used to ASCII characters.  
               Additional information:  
               Returns the formatter serial number, prefixed with  
               the PML_UNICODE_PREFIX.."  
::={ id 20 }  
                
                
engine-self-diagnostic OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The ENGINE-SELF-DIAGNOSTIC object reveals current engine		  
               failures; it returns a binary string of two-byte motor, clutch,		  
               solenoid, and sensor failure codes.  
               Additional information:  
               The ENGINE-SELF-DIAGNOSTIC object reveals current  
               Engine Failures; it returns a BINARY string of two-byte  
               Motor, Clutch, Solenoid and Sensor failure codes."  
::={ test 7 }  
                
                
engine-parameter OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The ENGINE-PARAMETER object returns a device specific set of		  
               engine parameters as a binary string of byte values. It will be		  
               necessary to have a decoder for each engine to interpret the		  
               data.  
               Additional information:  
               The ENGINE-PARAMETER object returns a device specific  
               set of engine parameters as a BINARY string of byte  
               values. It will be necessary to have a decoder for each  
               engine to interpret the data."  
::={ test 8 }  
                
                
default-media-name OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the media name that is used until the media		  
               name is changed by a print job command.  
               Additional information:  
               Returns or sets the media name that is used until the  
               media name is changed by a print job command.  
               This string must be one of the MEDIAn-NAME   
               objects.   
               This object is localized if the corresponding MEDIAn-NAME   
               object is localized.  
               The data for this object is stored in NVRAM."  
::={ settings-pdl 22 }  
                
                
override-media-name OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets a string identifying the media name that is to be used in		  
               place of the currently requested media. The substitution will		  
               continue until another media is selected. If set to a named		  
               media that is not currently available the requested media is		  
               not overridden.  
               Additional information:  
               When a request is received to print on a size and  
               type of media that is not currently available, this  
               object contains the desired media name as set by the  
               print job. This object should be set to a media name  
               that is currently available in the printer.  If a  
               paper mount request is not pending, attempting to get  
               or set this object will cause  
               <noSuchName> to be returned.  
               Setting this object to a string other than one of the  
               MEDIAn-NAME objects (MEDIA-NAMES-AVAILABLE is applied)  
               will cause a status of <badValue>  
               to be returned."  
::={ settings-prt-eng 2 }  
                
                
override-media-size OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eLedger(11),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eROC8K(19),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eISOandJISA3(27),  
		  eJISB5(45),  
		  eJISB4(46),  
		  eISOB5(65),  
		  eJapanesePostcardDouble(72),  
		  eMonarch(80),  
		  eCommercial10(81),  
		  eInternationalDL(90),  
		  eInternationalC5(91),  
		  eInternationalB5(100),  
		  eCustom(101),  
		  eUSLetterR(258),  
		  eISOandJISA4R(282),  
		  eUnknownMediaSize(32767)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the media size that is to be used in place of the		  
               currently requested media size.  
               Additional information:  
               When a request is received to print on a size and  
               type of media that is not currently available, this object  
               contains the desired size as set by the print job. This object  
               should be set to a media size that is currently available to the  
               printer. If a paper mount request is not pending, attempting to  
               get or set this object will cause <noSuchName>  
               to be returned."  
::={ settings-prt-eng 3 }  
                
                
marking-agent-highlights-density-setting OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the marking agent highlights density setting		  
               for each of the marking agents installed. The value of this		  
               object is in the range of -5..+5. The Marking Agent (aka Print)		  
               density is the instantaneous amount of marking agent applied to		  
               the media while printing. A value of -5 has the lowest print		  
               density, yeilding a lighter pageA value of +5 the highest print		  
               density, yielding a darker page.  
               Additional information:  
               Returns or sets the marking agent highlights density setting for each   
               of the marking agents installed. The value of this object is in the   
               range of -5..+5. The Marking Agent (aka Print) density is the instantaneous   
               amount of marking agent applied to the media while printing. A value of -5   
               has the lowest print density, yielding a lighter page. A value of +5 has the   
               highest print density, yielding a darker page."  
::={ marking-agent-density 2 }  
                
                
marking-agent-midtones-density-setting OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the marking agent midtones density setting for		  
               each of the marking agents installed. The value of this object		  
               is in the range of -5..+5. See		  
               MARKING-AGENT-HIGHLIGHTS-DENSITY-SETTING for a more specific		  
               description.  
               Additional information:  
               Returns or sets the marking agent midtones density setting for each   
               of the marking agents installed. The value of this object is in the   
               range of -5..+5. See MARKING-AGENT-HIGHLIGHTS-DENSITY-SETTING   
               for a more specific description."  
::={ marking-agent-density 3 }  
                
                
marking-agent-shadows-density-setting OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the marking agent shadows density setting for		  
               each of the marking agents installed. The value of this object		  
               is in the range of -5..+5. See		  
               MARKING-AGENT-HIGHLIGHTS-DENSITY-SETTING for a more specific		  
               description.  
               Additional information:  
               Returns or sets the marking agent shadows density setting for each   
               of the marking agents installed. The value of this object is in the   
               range of -5..+5. See MARKING-AGENT-HIGHLIGHTS-DENSITY-SETTING   
               for a more specific description."  
::={ marking-agent-density 4 }  
                
                
autocleaning-page-frequency OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Controls the number of pages between printing of the auto		  
               cleaning page (if enabled). Any device specific 'snap' behavior		  
               for this page interval will be specified in the device pos.  
               Additional information:  
               Controls the number of pages between printing of the auto  
               cleaning page (if enabled).  
               The legal values are 1000, 2000, 5000, 10000, and 20000.  
               All other values will return OK_NEAREST_LEGAL_VALUE_SUBSTITUTED."  
::={ settings-prt-eng 11 }  
                
                
autocleaning-page-size OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSLetter(2),  
		  eISOandJISA4(26)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Controls the size of paper used to print the auto cleaning page		  
               (if enabled).  
               Additional information:  
               Controls the size of paper used to print the auto cleaning page  
               (if enabled)."  
::={ settings-prt-eng 12 }  
                
                
finisher-image-rotation OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This PML object will provide the additional image rotation that		  
               is applied to a printed job depending on the presence or		  
               absence of a finisher device or the value of the		  
               SVM_ALWAYS_MATCH_OUTPUT_ORIENTATION variable.  
               Additional information:  
               This PML object will provide the additional image  
               rotation that is applied to a printed job depending  
               on the presence or absence of a finisher device   
               and/or the state of the IMAGE ROTATION menu element."  
::={ settings-prt-eng 31 }  
                
                
total-color-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of color pages printed by the device.  
               Additional information:  
               Total number of color pages printed by the device.  
               The valid range of this object is 0 to 2^24-1. When the number of  
               color pages printed exceeds the maximum color page count, the  
               value will roll to zero.  
               A duplexed sheet of media will cause the counter to be  
               incremented by two."  
::={ status-prt-eng 7 }  
                
                
duplex-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Total number of sheets of media that have been duplex printed.		  
               A sheet is counted if it travels through the duplex page path,		  
               regardless of whether or not marks are made on the page. The		  
               POS will indicate if the value is kept in NVRAM.  
               Additional information:  
               Total number of sheets of media that have been duplex  
               printed.  A sheet is counted if it travels through the  
               duplex page path, regardless of whether or not marks are  
               made on the page.    
               This value is kept in NVRAM however the NVRAM value is only   
               updated every 10 sheets. NOTE: The value returned by this object   
               will be incremented every sheet but if power is lost between  
               NVRAM updates up to 9 sheets of the count may be lost. The counter   
               will be reset to zero after 16,777,215 (2^24-1) pages. "  
::={ status-prt-eng 22 }  
                
                
print-engine-revision OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..16))  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Print engine revision string.  
               Additional information:  
               Print engine revision string.  The symbol set for this string is   
               Roman-8. "  
::={ status-prt-eng 26 }  
                
                
printer-cal-dhalf-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the page count when the last DHALF calibration		  
               occurred. A '-1' indicates that a calibration of this kind has		  
               not taken place yet. This object exists (and is meaningful)		  
               only in color printers.  
               Additional information:  
               Provides the page count when last DHALF calibration  
               occurred. A -1 indicates that a calibration of this  
               kind has not taken place yet. This object exists  
               (and is meaningful) only in color printers."  
::={ printer-calibration-dhalf 1 }  
                
                
printer-cal-dhalf-utc OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the time (in UTC - Universal Time Code format) when		  
               the last DHALF calibration occurred. This value could be zero		  
               if no calibration has taken place or if the printer lacked		  
               real-time. This object exists (and is meaningful) only in color		  
               printers.  
               Additional information:  
               Provides the time (in UTC - Universal Time Code format)  
               when last DHALF calibration occurred. This value could  
               be zero if no calibration has taken place and / or if  
               the printer lacked real-time. This object exists (and  
               is meaningful) only in color printers."  
::={ printer-calibration-dhalf 2 }  
                
                
printer-cal-dhalf-data1 OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides a device specific set of DHalf calibration data as a		  
               binary string of byte values. It will be necessary to have a		  
               decoder for each engine to interpret the data.  
               Additional information:  
               Provides a device specific set of Dhalf calibration data as a  
               binary string of byte values. It will be necessary to have a  
               decoder for each engine to interpret the data."  
::={ printer-cal-dhalf-data 1 }  
                
                
printer-cal-dhalf-data2 OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides a device specific set of DHalf calibration data as a		  
               binary string of byte values. It will be necessary to have a		  
               decoder for each engine to interpret the data.  
               Additional information:  
               Provides a device specific set of Dhalf calibration data as a  
               binary string of byte values. It will be necessary to  
               	       have a decoder for each engine to interpret the data."  
::={ printer-cal-dhalf-data 2 }  
                
                
printer-cal-cpr-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the page count when last CPR calibration occurred. A		  
               '-1' indicates that a calibration of this kind has not taken		  
               place yet. This object exists (and is meaningful) only in color		  
               printers.  
               Additional information:  
               Provides the page count when last CPR calibration  
               occurred. A -1 indicates that a calibration of this  
               kind has not taken place yet. This object exists  
               (and is meaningful) only in color printers."  
::={ printer-calibration-cpr 1 }  
                
                
printer-cal-cpr-utc OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the time (in UTC - Universal Time Code format) when		  
               the last CPR calibration occurred. This value could be zero if		  
               no calibration has taken place or if the printer lacked		  
               real-time. This object exists (and is meaningful) only in color		  
               printers.  
               Additional information:  
               Provides the time (in UTC - Universal Time Code format)  
               when last CPR calibration occurred. This value could  
               be zero if no calibration has taken place and / or if  
               the printer lacked real-time. This object exists (and  
               is meaningful) only in color printers."  
::={ printer-calibration-cpr 2 }  
                
                
printer-cal-cpr-data OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides a device specific set of CPR calibration data as a		  
               binary string of byte values. It will be necessary to have a		  
               decoder for each engine to interpret the data.  
               Additional information:  
               Provides a device specific set of CPR calibration data as a  
               binary string of byte values. It will be necessary to have a  
               decoder for each engine to interpret the data."  
::={ printer-calibration-cpr 3 }  
                
                
input-tray-auto-select OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Indicates if the device will automatically try to load media		  
               from the next input media tray in the auto-select sequence		  
               (defined by each device) when it cannot load media from the		  
               current tray. Locked trays will not be permitted in the		  
               auto-select sequence. This object has no meaning if there is		  
               only one unlocked input media tray.  
               Additional information:  
               Indicates if the device will automatically try to load  
               media from the next input media tray in the auto-select  
               sequence (defined by each device) when it cannot load  
               media from the current tray.  Locked trays will not be  
               permitted in the auto-select sequence.  This object has  
               no meaning if there is only one unlocked input media  
               tray."  
::={ settings-intray 2 }  
                
                
custom-paper-feed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the printer's custom paper dimension in the feed direction		  
               (direction parallel to the direction of paper feeding). The		  
               value for this object is specified in micrometers or		  
               tenthousandths of an inch, depending upon the value of		  
               CUSTOM-PAPER-DIM-UNIT. The valid range is engine-dependent and		  
               should be documented in the POS for each product.  
               Additional information:  
               Get/Set custom paper dimension (height).  
               The return/set value is either in micrometers or   
               10,000ths of inches.  A tray has to be in  
               custom switch or without media size sensor to be  
               able to set the custom dimension.   
               If it is successfully setting the dimension value,  
               the size of a tray is set to CUSTOM."  
::={ settings-intray 8 }  
                
                
custom-paper-xfeed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the printer's custom paper dimension in the cross-feed		  
               direction (direction ninety degrees relative to the direction		  
               of paper feeding). The value for this object is specified in		  
               micrometers or tenthousandths of an inch, depending upon the		  
               value of CUSTOM-PAPER-DIM-UNIT. The valid range is		  
               engine-dependent and should be documented in the POS for each		  
               product.  
               Additional information:  
               Get/Set custom paper dimension (width).  
               The return/set value is either in micrometers or   
               10,000ths of inches.  A tray has to be in  
               custom switch or without media size sensor to be  
               able to set the custom dimension.   
               If it is successfully setting the dimension value,  
               the size of a tray is set to CUSTOM."  
::={ settings-intray 9 }  
                
                
default-custom-paper-dim-unit OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eTenThousandthsOfInches(3),  
		  eMicrometers(4)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The units of measure used to specify the width and height of		  
               the printer's default custom paper size. The unit of measure of		  
               eTenThousandthsOfInches is 0.0001 inches.  
               Additional information:  
               The units of measure used to specify the width and   
               height of the printer's default custom paper size.  
               The unit of measure of eTenThousandthsOfInches is  
               0.0001 inches."  
::={ settings-intray 10 }  
                
                
default-custom-paper-feed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the printer's default custom paper size dimension in the		  
               feed direction (direction parallel to the direction of paper		  
               feeding). The value for this object is specified in micrometers		  
               or tenthousandths of an inch, depending upon the value of		  
               DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is		  
               engine-dependent and should be documented in the POS for each		  
               product.  
               Additional information:  
               Sets the printer's default custom paper size dimension   
               in the feed direction (direction parallel to the direction  
               of paper feeding). The value for this object is specified  
               in micrometers or tenthousandths of an inch, depending upon  
               the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid  
               range is engine-dependent and should be documented in the  
               POS for each product."  
::={ settings-intray 11 }  
                
                
default-custom-paper-xfeed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Sets the printer's default custom paper size dimension in the		  
               cross-feed direction (direction ninety degrees relative to the		  
               direction of paper feeding). The value for this object is		  
               specified in micrometers or tenthousandths of an inch,		  
               depending upon the value of DEFAULT-CUSTOM-PAPER-DIM-UNIT. The		  
               valid range is engine-dependent and should be documented in the		  
               POS for each product.  
               Additional information:  
               Sets the printer's default custom paper size dimension   
               in the cross-feed direction (direction ninety degrees  
               relative to the direction of paper feeding). The value  
               for this object is specified in micrometers or  
               tenthousandths of an inch, depending upon the value of  
               DEFAULT-CUSTOM-PAPER-DIM-UNIT. The valid range is  
               engine-dependent and should be documented in the POS  
               for each product."  
::={ settings-intray 12 }  
                
                
input-tray-max-media-feed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The maximum physical media size in the feed direction of this		  
               input device expressed in units of measure specified by INPUT-		  
               TRAY-MIN-MAX-DIM-UNIT. A value of (-1) implies 'unlimited', a		  
               value of (-2) implies 'unknown'.  
               Additional information:  
               The maximum physical media size in the feed direction of this   
               input device expressed in units of measure specified by  
               PrtInputDimUnit. A value of (-1) implies 'unlimited',  
               a value of (-2) implies 'unknown'.  
               Refer to Printer Management Standards web page,  
               http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, for more details in the original format  
               of the Standard Printer MIB."  
::={ settings-intray 14 }  
                
                
input-tray-max-media-xfeed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The maximum physical media size across the feed direction of a		  
               particular input device expressed in units of measure specified		  
               by INPUT-TRAY-MIN-MAX-DIM-UNIT. A value of (-1) implies		  
               'unlimited', a value of (-2) implies 'unknown'.  
               Additional information:  
               The maximum physical media size across the feed direction of this   
               input device expressed in units of measure specified by  
               PrtInputDimUnit. A value of (-1) implies 'unlimited',  
               a value of (-2) implies 'unknown'.  
               Refer to Printer Management Standards web page,  
               http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement, f  
               or more details in the original format  
               of the Standard Printer MIB."  
::={ settings-intray 15 }  
                
                
input-tray-min-media-feed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The minimum physical media size in the feed direction of a		  
               particular input device expressed in units of measure specified		  
               by PrtInputMinMaxDimUnit. A value of (-1) implies 'unlimited',		  
               a value of (-2) implies 'unknown'.  
               Additional information:  
               The minimum physical media size in the feed direction of this   
               input device expressed in units of measure specified by  
               PrtInputDimUnit. A value of (-1) implies 'unlimited',  
               a value of (-2) implies 'unknown'.  
               Refer to Printer Management Standards web page,  
               http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement,  
               for more details in the original format  
               of the Standard Printer MIB."  
::={ settings-intray 16 }  
                
                
input-tray-min-media-xfeed-dim OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The minimum physical media size across the feed direction of a		  
               particular input device expressed in units of measure specified		  
               by PrtInputMinMaxDimUnit. A value of (-1) implies 'unlimited',		  
               a value of (-2) implies 'unknown'.  
               Additional information:  
               The minimum physical media size across the feed direction of this   
               input device expressed in units of measure specified by  
               PrtInputDimUnit. A value of (-1) implies 'unlimited',  
               a value of (-2) implies 'unknown'.  
               Refer to Printer Management Standards web page,  
               http://bldlabs.boi.hp.com/BLDPrinterLab/Project/PrinterManagement,  
               for more details in the original format  
               of the Standard Printer MIB."  
::={ settings-intray 17 }  
                
                
               
tray1-media-size-loaded OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eFoolscap(10),  
		  eStatement(15),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eJISB5(45),  
		  eJapansePostcardDouble(72),  
		  eMonarch(80),  
		  eCommercial10(81),  
		  eInternationalDL(90),  
		  eInternationalC5(91),  
		  eInternationalB5(100),  
		  eCustom(101),  
		  eAnyCustomSize(32764),  
		  eAnySize(32765)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns the media size that is currently configuredconfigured		  
               in tray #1. This object can be set to indicate the media size		  
               currently loaded, if the printer supports input trays that can		  
               not sense the media size. Complete list of supported media		  
               sizes along with their dimensions are listed in the ''Media		  
               Size Table'' near the end of this document.  
               Additional information:  
               Returns the media size that is currently   
               configuredconfigured in tray #1. This object can be set  
               to indicate the media size currently loaded, if the  
               printer supports input trays that can not sense the  
               media size. Complete list of supported media sizes  
               along with their dimensions are listed in the ''Media  
               Size Table'' near the end of this document."  
::={ intray1 1 }  
                
                
tray1-phd OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the number of the Paper Handling Device that contains		  
               this input tray.  
               Additional information:  
               Provides the number of the Paper Handling Device that  
               contains this input tray."  
::={ intray1 12 }  
                
                
tray2-media-size-loaded OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eFoolscap(10),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eJISB5(45),  
		  eCustom(101),  
		  eAnyCustomSize(32764),  
		  eAnySize(32765)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns the media size that is currently configured in tray #2.		  
               Complete list of supported media sizes along with their		  
               dimensions are listed in the ''Media Size Table'' near the end		  
               of this document.  
               Additional information:  
               Returns the media size that is currently configured in  
               tray #2."  
::={ intray2 1 }  
                
                
tray2-phd OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the number of the Paper Handling Device that contains		  
               this input tray.  
               Additional information:  
               Provides the number of the Paper Handling Device that   
               contains this input tray."  
::={ intray2 12 }  
                
                
tray3-media-size-loaded OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eFoolscap(10),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eJISB5(45),  
		  eCustom(101),  
		  eAnyCustomSize(32764),  
		  eAnySize(32765)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns the media size that is currently configured in tray #3.		  
               Complete list of supported media sizes along with their		  
               dimensions are listed in the ''Media Size Table'' near the end		  
               of this document.  
               Additional information:  
               Returns the media size that is currently configured in  
               tray #3."  
::={ intray3 1 }  
                
                
tray3-phd OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the number of the Paper Handling Device that contains		  
               this input tray.  
               Additional information:  
               Provides the number of the Paper Handling Device that   
               contains this input tray."  
::={ intray3 12 }  
                
                
tray5-media-size-loaded OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eUSExecutive(1),  
		  eUSLetter(2),  
		  eUSLegal(3),  
		  eFoolscap(10),  
		  eROC16K(17),  
		  eJISExecutive(18),  
		  eISOandJISA5(25),  
		  eISOandJISA4(26),  
		  eJISB5(45),  
		  eCustom(101),  
		  eAnyCustomSize(32764),  
		  eAnySize(32765)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns the media size that is currently configured in tray #5.		  
               Complete list of supported media sizes along with their		  
               dimensions are listed in the ''Media Size Table'' near the end		  
               of this document.  
               Additional information:  
               Returns the media size that is currently configured in  
               tray #5."  
::={ intray5 1 }  
                
                
tray5-phd OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the number of the Paper Handling Device that contains		  
               this input tray.  
               Additional information:  
               Provides the number of the Paper Handling Device that  
               contains this input tray."  
::={ intray5 12 }  
                
                
overflow-bin OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the bin that will be used for additional sheets		  
               of media when the current bin is full and printing is allowed		  
               to continue.  
               Additional information:  
               Returns or sets the bin that will be used for additional  
               sheets of media when the current bin is full and  
               printing is allowed to continue.   
               The data for this object is stored in NVRAM."  
::={ settings-outbin 4 }  
                
                
outbin1-override-mode OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the device behavior when this output bin		  
               condition causes printing to stop.    	  
                   cCancelJob - The device cancels the job.    	  
                   cOutbinFullOverride - The device sends subsequent media to		  
                       the overflow bin.    	  
                   cOutbinAttentionOverride - The device ignores the attention		  
                       condition and continues printing.    	  
                   cBinderAttentionOverride - The device ignores the binder		  
                       attention condition and continues printing.    
               Additional information:  
               Returns or sets the device behavior when this output bin  
               condition causes printing to stop.  
               cCancelJob - The device cancels the job, regardless of other  
               bit settings.  
               cOutbinFullOverride - The device sends subsequent  
               media to the overflow bin.  If this bin is the  
               overflow bin, this bit is ignored.  
               cOutbinAttentionOverride - The device ignores the  
               attention condition and continues printing.  
               cBinderAttentionOverride - The device ignores the  
               binder attention condition and continues printing.  
                 
               This object describes the action that is performed when the  
               JOB-OUTPUT-AUTO-CONTINUE-TIMEOUT expires. If no bits  
               are set, no override action is taken (the printer  
               will continue to wait)."  
::={ outbin1 9 }  
                
                
marker-density-calibration OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNotCalibrating(1),  
		  eCalibrateALL(2),  
		  eCalibrateColor(3),  
		  eCalibrateColorPlaneRegistration(5),  
		  eCalibrateDrumPhaseAdjustment(6),  
		  eCalibrateBlackOnly(7)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns the calibration status or triggers a calibration cycle.		  
               All calibration procedures are used if set to eCalibrateALL. If		  
               set to eCalibrateColor then a full density engine calibration		  
               is triggered. If set to eCalibrateColorPlaneRegistration, then		  
               a Color Plane Registration calibration is triggered. If set to		  
               eCalibrateDrumPhaseAdjustment, then a Drum Phase Adjustment		  
               calibration is triggered. Note that eNotCalibrating and		  
               eCalibrateBlackOnly are read-only values. eNotCalibrating is		  
               returned when no calibrations are executing.		  
               eCalibrateBlackOnly is returned when a density engine		  
               calibration is executing while in MPACCO mode.  
               Additional information:  
               Returns the calibration status or triggers a calibration   
               cycle. All calibration procedures are used if set to  
               eCalibrateALL. If set to eCalibrateColor then a full  
               density engine calibration is triggered.  If set to  
               eCalibrateHalftone, then a Halftone calibration is triggered.  
               	       If set to eCalibrateColorPlaneRegistration, then a Color  
               Plane Registration calibration is triggered. If set to  
               eCalibrateDrumPhaseAdjustment, then a Drum Phase Adjustment  
               calibration is triggered.  
               	       Note that eNotCalibrating and eCalibrateBlackOnly are read-only  
               	       values.  eNotCalibrating is returned when no calibrations are  
               	       executing.  eCalibrateBlackOnly is returned when a density  
               	       engine calibration is executing while in MPACCO mode."  
::={ settings-marking-agent 11 }  
                
                
media-names-available OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The value of this object controls which of the MEDIAx-NAME		  
               objects are supported. If a bit is set to zero, then attempting		  
               to get or set the corresponding MEDIAx-NAME objects will return		  
               <noSuchName>.  
               Additional information:  
               Setting a bit to one will cause the corresponding  
               MEDIAn- objects to be available (attempting to access  
               an unavailable object will return <noSuchName>).  
               MEDIA1- objects are always present, as this is the default  
               media. If this object is set to a value that does not include  
               cMediaName2Available, that bit will be set and a status of  
               <noError> will be returned."  
::={ settings-print-media 1 }  
                
                
north-edge-offset OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the number of 300 dpi dots by which the image		  
               is shifted. Shift is relative to the leading edge of the medium		  
               as the medium flows through the marking engine with the side to		  
               be imaged facing the observer. The leading edge is the North		  
               edge and the other edges are defined by the normal compass		  
               layout of directions with the compass facing the observer. The		  
               adjustment is for all pages printed. A positive value moves the		  
               image away from the leading edge of the medium. A negative		  
               value moves the image closer to the leading edge of the medium.		  
               The value 0 will return the image to its factory default		  
               position.  
               Additional information:  
               Returns or sets the number of 300 dpi dots by which the image is  
               shifted.  Shift is relative to the leading edge of the medium as the  
               medium flows through the marking engine with the side to be imaged  
               facing the observer. The leading edge is the North edge and the  
               other edges are defined by the normal compass layout of directions  
               with the compass facing the ob server. The adjustment is for all  
               pages printed. A positive value moves the image away from the leading  
               edge of the medium. A negative value moves the image closer to the  
               leading edge of the medium.  The value 0 will return the image to  
               its factory default position.  
               The value of this object is stored in NVRAM."  
::={ settings-print-media 2 }  
                
                
media1-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 1 name.  
               Additional information:  
               The order of these objects is determined by the order of   
               SysOD_MediaTypeEnum.  The symbol set for this string is Roman-8.  "  
::={ media1 1 }  
                
                
media1-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 1. The length		  
               restriction is required to allow the media name to be displayed		  
               on the device's control panel. The device POS must state the		  
               maximum number of characters allowed. If the device also has a		  
               limitation on what characters in a character set can be used		  
               (e.g. only uppercase characters allowed), the POS should also		  
               state character restrictions.  
               Additional information:  
               The order of these objects is determined by the order of   
               SysOD_MediaTypeEnum.  Length restricted version of the media   
               name 1.  The length restriction is required to allow the media   
               name to be displayed on the device's control panel.    
               The maximum supported string length is 9 characters. If   
               the user entered string is too long, the device will store  
               the first 9 characters and will return the  
               <noError> status.  
               The characters must be in the range 20H to 7FH except 5C  
               cannot be used. The default symbol set is Roman-8 for  
               English; additional legal symbol sets are ISOLatin5,  
               ISOLatin2 and Windows31J. Setting this object with characters  
               outside of the range or of an illegal symbol set will cause an  
               error status of <badValue> to be returned.  
               This string is localized according to prtConsoleLocalization.  
               If this object represents a standard type, and the user  
               attempts to set the object, 'OK Nearest Legal Value Substituted'  
               will be returned, and the standard value is retained.  
               If this object represents a user defined type, and the user  
               attempts to set the object, then the set will be successfull."  
::={ media1 2 }  
                
                
media1-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 1 that have been printed. The device		  
               POS should state whether this value is lost across a power		  
               cycle or kept in NVRAM.  
               Additional information:  
               Number of sheets of media 1 that have been printed.  
               This page count is saved in NVRAM after every 10   
               pages. The maximum value is 4,294,967,295 which will never be  
               reached in normal operation.  
               The page count is incremented when a sheet of media is pulled   
               from an input tray. A duplex printed sheet will cause this   
               counter to be incremented by one."  
::={ media1 3 }  
                
                
media1-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               Displays the engine processing characterstics that are applied  
               to this media type."  
::={ media1 4 }  
                
                
media2-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 2 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media2 1 }  
                
                
media2-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 2. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media2 2 }  
                
                
media2-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 2 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media2 3 }  
                
                
media2-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media2 4 }  
                
                
media3-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 3 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media3 1 }  
                
                
media3-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 3. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media3 2 }  
                
                
media3-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 3 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media3 3 }  
                
                
media3-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media3 4 }  
                
                
media4-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 4 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media4 1 }  
                
                
media4-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 4. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media4 2 }  
                
                
media4-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 4 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media4 3 }  
                
                
media4-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media4 4 }  
                
                
media5-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 5 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media5 1 }  
                
                
media5-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 5. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media5 2 }  
                
                
media5-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 5 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media5 3 }  
                
                
media5-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media5 4 }  
                
                
media6-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 6 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media6 1 }  
                
                
media6-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 6. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media6 2 }  
                
                
media6-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 6 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media6 3 }  
                
                
media6-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media6 4 }  
                
                
media7-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 7 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media7 1 }  
                
                
media7-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 7. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media7 2 }  
                
                
media7-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 7 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media7 3 }  
                
                
media7-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media7 4 }  
                
                
media8-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 8 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media8 1 }  
                
                
media8-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 8. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media8 2 }  
                
                
media8-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 8 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media8 3 }  
                
                
media8-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media8 4 }  
                
                
media9-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 9 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media9 1 }  
                
                
media9-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 9. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media9 2 }  
                
                
media9-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 9 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media9 3 }  
                
                
media9-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media9 4 }  
                
                
media10-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 10 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media10 1 }  
                
                
media10-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 10. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media10 2 }  
                
                
media10-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 10 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media10 3 }  
                
                
media10-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media10 4 }  
                
                
media11-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 11 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media11 1 }  
                
                
media11-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 11. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media11 2 }  
                
                
media11-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 11 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media11 3 }  
                
                
media11-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media11 4 }  
                
                
media12-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 12 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media12 1 }  
                
                
media12-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 12. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media12 2 }  
                
                
media12-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 12 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media12 3 }  
                
                
media12-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media12 4 }  
                
                
media13-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 13 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media13 1 }  
                
                
media13-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 13. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media13 2 }  
                
                
media13-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 13 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media13 3 }  
                
                
media13-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media13 4 }  
                
                
media14-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 14 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media14 1 }  
                
                
media14-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 14. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media14 2 }  
                
                
media14-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 14 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media14 3 }  
                
                
media14-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media14 4 }  
                
                
media15-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 15 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media15 1 }  
                
                
media15-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 15. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media15 2 }  
                
                
media15-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 15 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media15 3 }  
                
                
media15-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media15 4 }  
                
                
media16-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 16 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media16 1 }  
                
                
media16-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 16. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media16 2 }  
                
                
media16-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 16 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media16 3 }  
                
                
media16-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media16 4 }  
                
                
media17-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 17 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media17 1 }  
                
                
media17-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 17. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media17 2 }  
                
                
media17-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 17 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media17 3 }  
                
                
media17-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media17 4 }  
                
                
media18-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 18 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media18 1 }  
                
                
media18-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 18. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media18 2 }  
                
                
media18-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 18 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media18 3 }  
                
                
media18-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media18 4 }  
                
                
media19-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 19 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media19 1 }  
                
                
media19-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 19. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media19 2 }  
                
                
media19-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 19 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media19 3 }  
                
                
media19-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media19 4 }  
                
                
media20-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 20 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media20 1 }  
                
                
media20-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 20. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media20 2 }  
                
                
media20-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 20 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media20 3 }  
                
                
media20-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media20 4 }  
                
                
media21-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 21 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media21 1 }  
                
                
media21-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 21. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media21 2 }  
                
                
media21-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 21 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media21 3 }  
                
                
media21-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media21 4 }  
                
                
media22-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 22 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media22 1 }  
                
                
media22-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 22. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media22 2 }  
                
                
media22-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 22 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media22 3 }  
                
                
media22-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media22 4 }  
                
                
media23-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 23 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media23 1 }  
                
                
media23-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 23. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media23 2 }  
                
                
media23-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 23 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media23 3 }  
                
                
media23-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media23 4 }  
                
                
media24-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 24 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media24 1 }  
                
                
media24-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 24. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media24 2 }  
                
                
media24-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 24 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media24 3 }  
                
                
media24-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media24 4 }  
                
                
media25-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 25 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media25 1 }  
                
                
media25-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 25. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media25 2 }  
                
                
media25-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 25 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media25 3 }  
                
                
media25-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media25 4 }  
                
                
media26-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..24))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Media 26 name.  
               Additional information:  
               See MEDIA1-NAME."  
::={ media26 1 }  
                
                
media26-short-name OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(1..9))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Length restricted version of the media name 26. See		  
               MEDIA1-SHORT-NAME for details.  
               Additional information:  
               See MEDIA1-SHORT-NAME."  
::={ media26 2 }  
                
                
media26-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Number of sheets of media 26 that have been printed. See		  
               MEDIA1-PAGE-COUNT for details.  
               Additional information:  
               See MEDIA1-PAGE-COUNT."  
::={ media26 3 }  
                
                
media26-engine-media-mode OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "The engine processing characteristics that are to be applied to		  
               this media. The processing characteristics are device		  
               specific.  
               Additional information:  
               See the description for MEDIA1-ENGINE-MEDIA-MODE."  
::={ media26 4 }  
                
                
engine-media-modes-supported1 OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "The list of engine media modes supported by the device. The		  
               modes are each separated by a comma character. An example		  
               string would be: 'Normal,Rough,Low,Vellum'.  
               Additional information:  
               The list of engine media modes supported by the device.   
               The modes are each separated by a comma character. An  
               example string would be: 'Normal,Rough,Low,Vellum'."  
::={ media-modes 1 }  
                
                
media-number-of-type-supported OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Indicates the maximum number of supported media types.  
               Additional information:  
               Indicates the number of supported media type.  
               This also indicates which bit in  
               MEDIA-NAMES-AVAILABLE is significant"  
::={ media-types 1 }  
                
                
non-assured-oht-page-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This is a count of the number of invalid (non-HP Laser Jet)		  
               transparencies that have been printed on. This value is		  
               incremented every time an invalid OHT is printed on It is reset		  
               whenever the fuser count is set to 0.  
               Additional information:  
               This is a count of the number of invalid (non HP Laser Jet)  
               transparencies that have been printed on. This value is  
               incremented every time an invalid OHT is printed on. It is reset  
               whenever the fuser count is set to 0."  
::={ media-counts 1 }  
                
                
media-size-west-edge-first-side-offset OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the number of 300 dpi dots by which the image		  
               is shifted relative to the west edge of the medium (see		  
               NORTH-EDGE-OFFSET). The adjustment is for the first printed		  
               side of the medium only. A positive value moves the image away		  
               from the west edge of the medium. A negative value moves the		  
               image closer to the west edge of the medium. The value 0 will		  
               return the image to its factory default position.  
               Additional information:  
               Returns or sets the number of 300 dpi dots by which the  
               image is shifted relative to the west edge of the medium  
               (see NORTH-EDGE-OFFSET). The adjustment is for the  
               first printed side of the medium only. A positive value  
               moves the image away from the west edge of the medium.  
               A negative value moves the image closer to the west edge  
               of the medium. The value 0 will return the image to its  
               factory default position.  
               The values in the sub array index are from the media size table  
               in the hpmib. This adjustment is done on a paper size by paper  
               size basis. The standard PCL5 codes for paper size are used for  
               the value used in the OID. Please see S_ARRAY_SUB1 for legal "  
::={ media-size 2 }  
                
                
media-size-west-edge-second-side-offset OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the number of 300 dpi dots by which the image		  
               is shifted relative to the west edge of the medium (see		  
               NORTH-EDGE-OFFSET). The adjustment is for the second printed		  
               side of the medium only. A positive value moves the image away		  
               from the west edge of the medium. A negative value moves the		  
               image closer to the west edge of the medium. The value 0 will		  
               return the image to its factory default position.  
               Additional information:  
               Returns or sets the number of 300 dpi dots by which the  
               image is shifted relative to the west edge of the medium  
               (see NORTH-EDGE-OFFSET). The adjustment is for the  
               second printed side of the medium only. A positive value  
               moves the image away from the west edge of the medium.  
               A negative value moves the image closer to the west edge  
               of the medium. The value 0 will return the image to its  
               factory default position. The values in the sub array index  
               are from the media size table in the hpmib.  
               This adjustment is done on a paper size by paper size basis.  
               The standard PCL5 codes for paper size are used for the value  
               used in the OID. Please see S_ARRAY_SUB1 for legal values.  
               The data for this object is stored in NVRAM."  
::={ media-size 3 }  
                
                
media-size-west-edge-side-offset-by-tray OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or sets the number of 300 dpi dots by which the image		  
               is shifted relative to the west edge of the medium (see		  
               NORTH-EDGE-OFFSET). A positive value moves the image away from		  
               the west edge of the medium. A negative value moves the image		  
               closer to the west edge of the medium. The value 0 will return		  
               the image to its factory default position. Each OID binding		  
               corresponds to a valid tray number for this product. There can		  
               be a maximum of 15 trays, a combination of internal and		  
               external trays. Products that support other combinations of		  
               trays will specify this information in the device pos. The data		  
               for this object is stored in NVRAM.  
               Additional information:  
               Returns or sets the number of 300 dpi dots by which the  
               image is shifted relative to the west edge of the medium  
               (see NORTH-EDGE-OFFSET). A positive value moves the  
               image away from the west edge of the medium. A negative  
               value moves the image closer to the west edge of the medium.  
               The value 0 will return the image to its factory default  
               position.  
                 
               Each OID binding corresponds to a valid tray number  
               for this product. There can be a maximum of 15 trays, a  
               combination of internal and external trays. Products that  
               support other combinations of trays will specify this  
               information in the device pos. The data for this object  
               is stored in NVRAM."  
::={ media-size 4 }  
                
              
color-supply-out-action OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eStop(1),  
		  eAutoContinueBlack(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This PML object can be used to change the behavior of the		  
               printer when a Color Cartridge reaches OUT. When this PML		  
               Object is set to eStop, the printer will be offline when a		  
               Color Cartridge reaches OUT. When this PML object is set to		  
               eAutoContinueBlack, then the printer will continue printing in		  
               Mono provided the Black cartridge has not reached OUT.  
               Additional information:  
               This corresponds to the menu setting 'Color Supply Out'.This  
               object can be changed by the control panel or by the PJL  
               variable. It can have any of the following enumerated values-  
               eStop(1), eAutoContinueBlack(2). "  
::={ settings-system 34 }  
                
                
control-panel-supplies-status-message OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eShow(1),  
		  eDontShow(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This PML object can be used to enable or disable supplies		  
               status messages from being displayed on the control panel.    	  
                   eShow - show the status messages on the control panel.    	  
                   eDontShow - do not show the status messages on the control		  
                       panel.     
               Additional information:  
               . This PML Object can be used to enable or disable the supplies  
               status messages from being displayed on the control panel.  
               eShow      Show the status messages on the control panel.  
               eDontShow  Do not show the status messages on the control panel."  
::={ settings-system 44 }  
                
                
configurable-low-threshold-setting OBJECT-TYPE  
  SYNTAX      INTEGER(0..100)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This PML object can be used to configure the low threshold for		  
               supplies.  
               Additional information:  
               This PML object can be used to configure the Low Threshold for Supplies."  
::={ settings-prt-eng 24 }  
                
                
supplies-replace-action-at-setting OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eStopAtLow(1),  
		  eStopAtOut(2),  
		  eOverrideAtOut(4)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object can be used to change the setting of menu item		  
               REPLACE SUPPLIES. The behavior of the printer when a supply		  
               reaches low changes in accordance with the setting of this PML		  
               Object. If the option eStopAtLow is selected printer will stop		  
               when a supply reaches LOW. If the option eStopAtOut is selected		  
               then printer will stop when a supply reaches OUT. If the		  
               options eStopAtMaxLife (supported only on Mono products) is		  
               selected, the printer will continue past supply OUT. If the		  
               option eOverrideAtOut or eOverrideAtOut2 (supported only on		  
               Color products) is selected then printer will continue past OUT		  
               in override mode. This option is not writeable. That is using		  
               this PML object the setting could be changed to any option		  
               other than eOverrideAtOut and eOverrideAtOut2.  
               Additional information:  
               This PML object can be used to change the setting of the menu   
               item REPLACE SUPPLIES. The behavior of the printer when a supply  
               		 hits low changes in accordance with the setting of this PML Object.  
               		 1. eStopAtLow - Printer will stop when a supply reaches low.  
               		 2. eStopAtOut - Printer will stop when a supply reaches out.  
               		 3. eOverrideAtOut[Read-only, Color Products] - Printer will continue  
               		    print past out in override mode."  
::={ settings-prt-eng 25 }  
                
                
supply-out-user-configured-override-limit OBJECT-TYPE  
  SYNTAX      INTEGER(0..100000)  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This PML object reports the user configured cartridge out		  
               override page limit.  
               Additional information:  
               This PML object reports the user configured cartridge out override  
               limit."  
::={ settings-prt-eng 26 }  
                
                
cartridge-out-override-control OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      write-only  
  STATUS      optional  
  DESCRIPTION "This PML object is used to control Cartridge Out Override		  
               feature.  
               Additional information:  
               This object is used for the following purposes:  
               1. Enable/disable cartridge out override through  
               SUPPLIES_REPLACE_ACTION_AT_PML Object.  
               2. Enable/disable Toner Out Limit: When toner out limit is disabled  
               using this PML Object, engine will not be taken offline when a  
               cartridge reaches toner out. Engine will continue to print and will  
               be in Override mode until other limits are reached.  
               3. Enable/disable CRG R&D Limit: When CRG R&D limit is disabled  
               using this PML Object, engine will not be taken offline when CRG  
               R&D limit for printing in override is reached for any out cartridge.  
               Engine will continue to print and will be in Override mode until  
               other limits are reached."  
::={ settings-prt-eng 27 }  
                
                
supply-out-action-support OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to determine if a particular capability		  
               that allows printing to continue after one or more cartridge		  
               has reached out is supported by the device. The collection bits		  
               include: cSupplyOutOverride - indicates that continuing to		  
               print with an out supply in use is supported.		  
               cMonochromePrintingAfterColorCartridgeOut - indicates that		  
               continuing to print in monochrome after a color cartridge is		  
               out is supported. cPrintingToMaxLife - indicates that printing		  
               until 'max life' is reached is supported [monochrome only].  
               Additional information:  
               This object is used to determine what capabilities are supported  
               by the device for allowing printing to continue after one or more  
               cartridges have reached out. The collection bits include:  
               cCartridgeOutOverride - indicates that continuing to print with  
               an out cartridge in use is supported.  
               cMonochromePrintingAfterColorCartridgeOut - indicates that  
               continuing to print with monochrome after a color cartridge is  
               out is supported."  
::={ status-prt-eng 48 }  
                
                
supply-out-device-state OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNoSupplyOut(1),  
		  eOffline(2),  
		  eCartridgeOutOverride(3),  
		  eMonochromePrintingAfterColorCartridgeOut(4)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This PML object indicates the current behavior of the device if		  
               one or more supplies have reached out. If no supply has reached		  
               out, the value of this PML object is eNoSupplyOut. If one or		  
               more supplies have reached out, the value of this PML object		  
               will indicate if the printer is online and if so what mode is		  
               being used to continue printing.  
               Additional information:  
               This object indicates the current behavior of the device if one  
               or more supplies have reached out. The enums represent:  
               eNoSupplyOut - No supplies have reached out.  
               eOffline - Printer is offline since one or more supplies have  
               reached out.  
               eCartridgeOutOverride - The cartridge override out is active.  
               eMonochromePrintingAfterColorCartridgeOut - Monochrome printing  
               after a color cartridge out is active."  
::={ status-prt-eng 49 }  
                
                
supply-after-out-state OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to read and write the various status flags		  
               indicating whether the consumable was used after out. The		  
               collection bits supported include:    	  
                   cNotUsedAfterOut - indicates the consumable was not used in		  
                       any capacity after out. If cUsedAfterOutInOverrideMode		  
                       or cUsedAfterOutInMonoPrintingAfterColorOutMode is set,		  
                       this flag will not be set.    	  
                   cInstalledWhileInOverrideMode - indicates the consumable		  
                       was installed while Supply Out Override was activated.		  
                          	  
                   cUsedAfterOutInOverrideMode - indicates the consumable was		  
                       used after out while Supply Out Override was activated.		  
                          	  
                   cInstalledWhileInMonoPrintingAfterColorOutMode - indicates		  
                       the consumable was installed while MPACCO was		  
                       activated.    	  
                   cUsedAfterOutInMonoPrintingAfterColorOutMode - indicates		  
                       the consumable was used after out while MPACCO was		  
                       activated.     
               Additional information:  
               This object is used to read the various status flags indicating  
               whether the consumable was used after out. The collection bits include:  
               cNotUsedAfterOut - indicates the consumable is not used after out.  
               cUsedAfterOutInOverrideMode - indicates the consumable was used  
               after out while cartridge out override was actiavted.  
               cInstalledWhileInMonoPrintingAfterColorOutMode - indicates that  
               the consumable was installed while MPACCO was activated.  
               cUsedAfterOutInMonoPrintingAfterColorOutMode - indicates that the  
               consumable was after out while MPACCO was activated."  
::={ status-prt-eng 50 }  
                
                
consumable-status-formatter-color-page-count OBJECT-TYPE  
  SYNTAX      INTEGER(0..32768)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to report the number of color pages that		  
               have been printed by this consumable.  
               Additional information:  
                This object is used to report the number of color pages that  
               have been printed by a consumable."  
::={ consumable-status 46 }  
                
                
consumable-status-page-count-out-while-cartridge-out-override-active OBJECT-TYPE  
  SYNTAX      INTEGER(0..65535)  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This PML object is used to report the number of pages that have		  
               been printed while this consumable was out and Cartridge Out		  
               Override was active.  
               Additional information:  
               This object is used to report the number of pages that have been  
               printed while this consumable was out and cartridge out override  
               was active. Note that the object has write access in debug mode."  
::={ consumable-status 60 }  
                
                
consumable-string-information OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..287))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object is used to read and write the string value that		  
               describes the consumable information."  
::={ consumable-string 1 }  
                
                
consumable-string-information-reset OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  ePresetToNVRAM(1)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object is used to reset (set back to factory default) or		  
               read the current status of the corresponding information		  
               string. When Set to eResetToDefault, this object can be used to		  
               reset the corresponding information object back to its factory		  
               default value. Setting this object with an enumerated value of		  
               eCustomized has no effect. When a Get operation is performed on		  
               this object it will return a value eResetToDefault if still set		  
               to its factory value. It will return eCustomized if the		  
               corresponding information value has been set to a custom		  
               value.  
               Additional information:  
               This object returns ePresetToNVRAM(1) if CONSUMABLE-STRING-INFORMATION is currently set to the default string. It will return eCustomized(2) otherwise. However, we can explicitly set this object only to ePresetToNVRAM(1) and not eCustomized(2)."  
::={ consumable-string 2 }  
                
                
consumable-reorder-url OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..64))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object is used to read and write the URL that can be used		  
               to reorder consumables for this device. This URL is set at the		  
               factory but can be updated by a reseller or third party.  
               Additional information:  
               The URL can be up to 64 characters long."  
::={ consumables 2 }  
                
                
consumable-current-state OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This PML object returns the current state of the particular		  
               consumable.    	  
                   cAuthLevel1 - Consumable is at Authentication Level 1    	  
                   cAuthLevel2 - Consumable is at Authentication Level 2    	  
                   cAuthLevel3 - Consumable is at Authentication Level 3    	  
                   cAuthLevel4 - Consumable is at Authentication Level 4    	  
                   cAuthLevel5 - Consumable is at Authentication Level 5    	  
                   cGenuineHPUnsupported - Cartridge is GenuineHP intended for		  
                       another product    	  
                   cDefectiveMemory - Cartridge has a defective memory tag    	  
                   cMissingMemory - Memory tag is missing from the cartridge		  
                          	  
                   cLowCondition - Consumable has reached the engine low		  
                       threshold    	  
                   cOutCondition - Consumable has reached its out threshold   	                           
                   cIncorrect - Cartridge inserted is not the correct one    	  
                   cMissing - Consumable is missing from the printer    	  
                   cConfigurableLow - Consumable has reached the configurable		  
                       low threshold value    	  
                   cStatusArevalid - The status reported on other bits are		  
                       valid only if the bit is set to 1. If it is 0, the		  
                       values are invalid.    	  
                   cExpired - Is the cartridge expired, which is determined   	                           
                   by the formatter.   	  
                   cFailure - Cartridge has failed determined by the engine.		  
                          	  
                   cLeak - Cartridge has a leak as determined by the engine.		  
                          	  
                   cUnknownManufacturer - the brand of the cartridge is    	  
                   unknown as determined by the engine.    	  
                   cUnsupported --- Cartridge is not supported as determined		  
                          	  
                   by the engine.    	  
               These are the possible states and whenever the consumable is in		  
               any of these states, the appropriate bit will be set. The		  
               cLowCondition will be set when the consumable reaches the		  
               engine low threshold, and cConfigurableLow will be set when the		  
               consumable reaches the Configurable Low threshold value. For		  
               non-cartridge supplies only cLowCondition, cOutCondition, and		  
               cMissing will be supported.  
               Additional information:  
               This object returns the current state of the particular consumable.  
               cAuthLevel1 - Consumable is at Authentication Level 1  
               cAuthLevel2 - Consumable is at Authentication Level 2  
               cAuthLevel3 - Consumable is at Authentication Level 3  
               cAuthLevel4 - Consumable is at Authentication Level 4  
               cGenuineHPUnsupported - Cartridge is GenuineHP intended for another product  
               cDefectiveMemory - Cartridge has a Defective Memory  
               cMissingMemory - Memory is Missing from the Cartridge  
               cLowCondition - Consumable has reached its low threshold  
               cOutCondition - Consumable has reached its out threshold  
               cIncorrect - Cartridge inserted is not the correct one  
               cMissing - Consumable is Missing from the Printer  
               cConfigurableLow - Consumable has reached the  
               configurable low threshold value  
               cStatusAreValid - The Status reported on other bits are valid only if  
               this bit is set to 1. If it is 0, the values are invalid.  
               These are the possible states and whenever a Consumable is in any of these  
               states, the appropriate bit will be set. For Non Cartridge Supplies only  
               cLowCondition, cOutCondition and cMissing will be supported."  
::={ consumables 7 }  
                
                
device-used-while-cartridge-out-override-active OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eNotUsed(1),  
		  eUsed(2)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Returns eUsed if the device has ever been used while Cartridge		  
               Out Override is activated. Merely enabling cartridge out		  
               override will not cause eUsed to be returned. Cartridge Out		  
               Override must be activated by a cartridge becoming out and		  
               device must be used in that mode.  
               Additional information:  
               This PML object can be used to determine whether the device has  
               ever been used while cartridge out override is activated. Merely  
               enabling cartridge out override will not cause eUsed to be  
               returned. Cartridge out override must be activated by a cartridge  
               becoming out and device must be used in that mode."  
::={ consumables 9 }  
                
                
consumable-notification-status OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "This object is used to read and write the various status flags		  
               supported by this consumable. For Laserjet 4700 MFP the collection bits		  
               supported include:    	  
                   cClient1ReorderNotificationSent - indicates whether EWS		  
                       (Embedded Web Server) has already sent the reorder		  
                       notification e-mail for this consumable. This bit can		  
                       be both read and written.    	  
                   cClient2ReorderNotificationSent - indicates whether WJA		  
                       (Web Jet Admin) has already sent the reorder		  
                       notification e-mail for this consumable. This bit can		  
                       be both read and written.    	  
                   cClient3ReorderNotificationSent - for future implementation		  
                          	  
                   cClient4ReorderNotificationSent - for future implementation		  
                          	  
                   cClient5ReorderNotificationSent - for future implementation		  
                          	  
                   cClient1ReplaceNotificationSent - indicates whether EWS		  
                       (Embedded Web Server) has already sent the replace		  
                       notification e-mail for this consumable. This bit can		  
                       be both read and written.    	  
                   cClient2ReplaceNotificationSent - indicates whether WJA		  
                       (Web Jet Admin) has already sent the replace		  
                       notification e-mail for this consumable. This bit can		  
                       be both read and written.    	  
                   cClient3ReplaceNotificationSent - for future implementation		  
                          	  
                   cClient4ReplaceNotificationSent - for future implementation		  
                          	  
                   cClient5ReplaceNotificationSent - for future implementation		  
                           
               Additional information:  
               If the cartridge is deemed to be NonHP, then this object will not exist.  
               This object will have 1 sub arrays for the consumable.  
               The client1 and 2 currently are assingned to EWS and WJA the remaining client are  
               reserved for the future third party pml tools. A client is requiered to set only his assigned  
               bit for reorder or replace notification. A client using other client's bit for reorder replace   
               will result in the other client being not able to set the notification.  
               Ex: For EWS ReOrderNotification it will send 0x00010000 and   
               For EWS ReplaceNotification it will send 0x00000001  
               For WJA ReOrderNotification it will send 0x00020000 and  
               For WJA ReplaceNotification it will send 0x00000002"  
::={ consumables 10 }  
                
                
consumable-life-usage-units-remaining OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object reports the current estimate of the number of usage		  
               units that remain before this supply is depleted. An installed		  
               supply that cannot report such a number will return a value of		  
               -2. It is the reponsibility of the host application to query		  
               each supply in order to determine an overall device		  
               USAGE-UNITS-REMAINING number - the lowest value returned. The		  
               unit of measure for this life estimate is determined by reading		  
               the corresponding CONSUMABLE-LIFE-USAGE-UNITS object.  
               Additional information:  
               This object will return the Pages or Estimated Pages remaining for   
               the speciffic supply requested by the leaf node of this object."  
::={ consumables-life 1 }  
                
                
consumable-life-usage-units OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  ePagesRemaining(1),  
		  eEstimatedPagesRemaining(2)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object reports current usage units in use by the		  
               corresponding CONSUMABLE-LIFE-USAGE-UNITS-REMAINING object.  
               Additional information:  
               This object returns the units that CONSUMABLE-LIFE-USAGE-UNITS-REMAINING  
               is returned in.  Either ePagesRemaining(1) or eEstimatedPagesRemaining(2)."  
::={ consumables-life 2 }  
                
                
consumable-life-low-threshold OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to report and modify a threshold value		  
               indicating the point in the life of a consumable or supply at		  
               which a transition to a LOW state will occur."  
::={ consumables-life 3 }  
                
                
printer-average-marking-agent-units-per-gram OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to read the marking agent units of measure		  
               per gram. This is typically a conversion factor for converting		  
               pixels of toner to grams. This pixels-per-gram value is used to		  
               calculate the estimated number of pages remaining for a given		  
               marking agent."  
::={ printer-average 4 }  
                
                
printer-average-marking-agent-coverage-actual OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object is used to read the actual average marking agent		  
               coverage for a given color plane. It is a real number that		  
               represents percent coverage and will read from 0 to 100%. This		  
               object will return the same value as		  
               PRINTER-AVERAGE-MARKING-AGENT-COVERAGE except under certain		  
               conditions which will be specified in the device POS."  
::={ printer-average 5 }  
                
                
default-vertical-black-resolution OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the value of the default vertical black		  
               resolution. The units are dots per inch.  
               Additional information:  
               In $product_str changing this OID also causes  
               DEFAULT-HORIZONTAL-BLACK RESOLUTION to change.  
               DEFAULT-HORIZONTAL-BLACK-RESOLUTION and  
               DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the  
               same.  The supported values are:  
               LaserJet 4100: 300, 600, 1200  
               Color Products: 600  
               LaserJet 9000: 300, 600     
               Setting to an unsupported value causes the printer  
               to substitute in a snap value and  
               to return <noError> status.    
               The snap values are as follow:    
               LaserJet 4100:    
                 
               450 >= n < 900 snaps to 600    
               n >= 900 snaps to 1200     
               Color Products:    
               n snaps to 600  
               LaserJet 9000:    
               n < 450 snaps to 300    
               n >=450 snaps to 600  "  
::={ settings-pdl 8 }  
                
                
default-horizontal-black-resolution OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the value of the default horizontal black		  
               resolution. The units are dots per inch.  
               Additional information:  
               In $product_str changing this object also causes  
               DEFAULT-VERTICAL-BLACK RESOLUTION to change.  
               DEFAULT-HORIZONTAL-BLACK-RESOLUTION and  
               DEFAULT-VERTICAL-BLACK-RESOLUTION must always be the  
               same.  The supported values are:  
               LaserJet 4100: 300, 600, 1200  
               Color Products: 600  
               LaserJet 9000: 300, 600     
               Setting to an unsupported value causes the printer  
               to substitute in a snap value and to  
               return <noError> status.    
               The snap values are as follow:    
               LaserJet 4100:    
               n < 450 snaps to 300    
               450 >= n < 900 snaps to 600    
               n >= 900 snaps to 1200     
               Color Products:    
               n snaps to 600  
               LaserJet 9000:    
               n < 450 snaps to 300    
               n >=450 snaps to 600  "  
::={ settings-pdl 9 }  
                
                
default-page-protect OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the default page protection behavior. If		  
               eOff, the device does not reserve memory for holding the entire		  
               raster form of a processed page. If eOn, then memory is		  
               reserved. If eAuto, the device determines the amount of memory		  
               to reserve.  
               Additional information:  
               Setting to eOn causes MET to be more conservative, but  
               it will not allocate memory to hold an entire  
               rasterized page."  
::={ settings-pdl 10 }  
                
                
default-bits-per-pixel OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Controls the number of levels used (per pixel) when printing		  
               grayscale or color images."  
::={ settings-pdl 39 }  
                
                
default-ret OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eLight(2),  
		  eMedium(3),  
		  eDark(4),  
		  eNotSet(5)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Returns or changes the Resolution Enhancement Technology		  
               setting. Devices that only support eOff and eOn should map all		  
               other values to eOn and always return the same non-eOff value		  
               to indicate on. The list of supported values should be		  
               documented in the device POS.  
               Additional information:  
               Setting this object may cause a status of <noError> to be  
               returned, but the new value will not take effect until a job  
               boundary is reached. If a get is done on object before the job  
               boundary is reached, the value last set will be returned.  
               The value of this object is saved over a powercycle.    
               This object exists on monochrome printers only."  
::={ imaging 5 }  
                
                
                
web-server-url OBJECT-TYPE  
  SYNTAX      OCTET STRING (SIZE(0..64))  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "A Universal Resource Locator (URL) from which the Embedded Web		  
               Server can be configured. Any limitation on the size of this		  
               URL will be specified in the device POS."  
::={ settings-webserver 2 }  
                
                
web-server-security OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Each collection bit represents a device or Embedded Web Server		  
               feature that can be enabled or disabled via this object."  
::={ settings-webserver 3 }  
                
                
firmware-download-write-status-supported OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eFalse(1),  
		  eTrue(2)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object provides information on whether the printer has the		  
               ability to communicate the write-status of the firmware		  
               download while the download is taking place."  
::={ firmware-download 1 }  
                
                
firmware-download-write-time OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "If the design of the firmware-download implementation does not		  
               allow PML interaction during the download process, this value		  
               provides an estimation of the time where the printer will not		  
               be able to engage in PML communication.  
               Additional information:  
               If the design of the firmware-download   
               			implementation does not allow PML interaction during   
               			the download process, this value provides an   
               			estimation of the time where the printer will not be   
               			able to engage in PML communication. The calculated  
               			time is expected to be 140 secs. However, this time  
               			may increase as high as 280 secs as the flash part   
               			nears the maximum flash count."  
::={ firmware-download 2 }  
                
                
firmware-download-write-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Tells the number of times that firmware has been downloaded to		  
               the flash part.  
               Additional information:  
               Tells the number of times that firmware has been  
               	downloaded to the flash part. The default value will  
               			vary depending on how many times the firmware is  
               			rolled before shipping."  
::={ firmware-download 3 }  
                
                
firmware-download-current-state OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eIdle(1),  
		  eReceivingImage(2),  
		  eReceivedImageError(3),  
		  eVerifyingImage(4),  
		  eVerifiedImageError(5),  
		  eWritingImage(6),  
		  eWritingImageError(7),  
		  eDownloadComplete(8),  
		  eOKtoShutDown(9),  
		  eCancelDownload(10),  
		  eShuttingDown(11)  
		  }  
  ACCESS      read-write  
  STATUS      optional  
  DESCRIPTION "Provides the current or last reportable state of the firmware		  
               download process. The current state may not necessarily be the		  
               current state, but could be the post-mortem state."  
::={ firmware-download 4 }  
                
                
firmware-download-maximum-write-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Reports the manufacturer specified number of times that		  
               firmware can be downloaded to the flash part. A value of -1		  
               means that there is no limit. A value of 0 means that		  
               downloading firmware is not permitted by this part. Any other		  
               positive integer value corresponds to the number of times that		  
               firmware can be downloaded to the flash part.  
               Additional information:  
               Reports the manufacturer specified number of   
               			times that firmware can be downloaded to the flash   
               			part.  A value of -1 means that there is no limit.    
               			A value of 0 means that downloading firmware is not   
               			permitted by this part.  Any other positive integer   
               			value corresponds to the number of times that   
               			firmware can be downloaded to the flash part. The   
               			current maximum write count is 500. This may change  
               			as flash technology evolves."  
::={ firmware-download 5 }  
                
                
firmware-download-name OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      mandatory  
  DESCRIPTION "This returns the name of the printer. This should match the		  
               name in the header of the upgrade image being sent to the flash		  
               part. If the name does not match with the name returned then		  
               the image that we are attempting to download does not upgrade		  
               the printer firmware.  
               Additional information:  
               This object returns the HP name of the printer.    
               			     This should match what is in the PJL header of the RFU job  
               			     Web Jet Admin uses this to ensure the printer is available  
               		   	     to be upgraded."  
::={ firmware-download 6 }  
                
                
firmware-download-version OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      mandatory  
  DESCRIPTION "This object will return a string value representing the current		  
               revision of firmware that the printer is operating with. This		  
               is used to determine if code needs to be upgraded when an		  
               firmware bundle comes in, in an upgrade job.  
               Additional information:  
               Web Jet Admin uses the version string that is returned to  
               			     determine what peices of an RFU bundle need to be upgraded   
               			     when an RFU job is being built. This objects will return  
               			     the version string of the printer."  
::={ firmware-download 7 }  
                
                
upgradable-devices-write-status-supported OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eFalse(1),  
		  eTrue(2)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "This object provides information on whether the upgradable		  
               device has the ability to communicate the write-status of the		  
               upgrade while the upgrade is taking place."  
::={ upgradable-devices 1 }  
                
                
upgradable-devices-write-time OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "If the design of the device upgrade implementation does not		  
               allow PML interaction during the download process, this value		  
               provides an estimation of the time where the device will not be		  
               able to engage in PML communication. The time returned will		  
               depend upon what device is attempting to be upgraded."  
::={ upgradable-devices 2 }  
                
                
upgradable-devices-write-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Tells the number of times that firmware for device X has been		  
               downloaded to the flash part. The default value will vary		  
               depending on how many times the firmware is rolled before		  
               shipping."  
::={ upgradable-devices 3 }  
                
                
upgradable-devices-current-state OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eIdle(1),  
		  eReceivedImage(2),  
		  eReceivedImageError(3),  
		  eVerifiedImage(4),  
		  eVerifiedImageError(5),  
		  eWritingImage(6),  
		  eWritingImageError(7),  
		  eUpgradeComplete(8),  
		  eUpgradeSkipped(9)  
		  }  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Provides the current or last reportable state of the device		  
               upgrade process. The current state may not necessarily be the		  
               current state, but could be the post-mortem state."  
::={ upgradable-devices 4 }  
                
                
upgradable-devices-max-write-count OBJECT-TYPE  
  SYNTAX      INTEGER  
  ACCESS      read-only  
  STATUS      optional  
  DESCRIPTION "Reports the manufacturer specified number of times that		  
               firmware for device X can be downloaded to the flash part. A		  
               value of -1 means that there is no limit. A value of 0 means		  
               that downloading firmware is not permitted by this part. Any		  
               other positive integer value corresponds to the number of times		  
               that the firmware for device X can be downloaded to the flash		  
               part. The current maximum write count is 500. This may change		  
               as flash technology evolves."  
::={ upgradable-devices 5 }  
                
                
upgradable-devices-name OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      mandatory  
  DESCRIPTION "This returns the name of the upgradable device. This should		  
               match the name in the header of the upgrade image being sent to		  
               the flash part. If the name does not match with any of the		  
               names returned then the device that we are attempting to		  
               upgrade is unavailable for upgrading.  
               Additional information:  
               This object returns the HP name of the printer and the upgradable  
               			     devices. There is one Name object per upgradable device.    
               			     This should match what is in the PJL header of the RFU job  
               			     Web Jet Admin uses this to ensure the printer or device  is  
               			     available to be upgraded."  
::={ upgradable-devices 6 }  
                
                
upgradable-devices-version OBJECT-TYPE  
  SYNTAX      OCTET STRING  
  ACCESS      read-only  
  STATUS      mandatory  
  DESCRIPTION "This object will return a string value representing the current		  
               revision of firmware that device X is operating with. This is		  
               used to determine if code needs to be upgraded when a firmware		  
               bundle comes in, in an upgrade job.  
               Additional information:  
               Web Jet Admin uses the version string that is returned to  
               			     determine what peices of an RFU bundle need to be upgraded   
               			     when an RFU job is being built. This internal object will   
               			     return the current version string of the printer or device   
               			     that it corresponds to."  
::={ upgradable-devices 7 }  
                
                
remote-upgrade-enable OBJECT-TYPE  
  SYNTAX      INTEGER {  
		  eOff(1),  
		  eOn(2)  
		  }  
  ACCESS      read-write  
  STATUS      mandatory  
  DESCRIPTION "Enables or disables the ability to upgrade the firmware		  
               associated with any device that is available to be upgraded.		  
               This will be set to on or off at the RFU level in that if this		  
               mode is on any available device can be upgraded and if this		  
               mode is off none of the devices can be upgraded. There is not		  
               an individual mode for each device. Trying to set this to a		  
               value other than eOn or eOff will cause an UnsupportedValue		  
               error to occur."  
::={ upgradable-devices 8 }  
                
                
END
